-9-
Phase Selection
(Programmable for Patterns 1-25 only)
Each head has two Phases, an “On” phase and an “Off” phase (or a “Color 1”
Phase and a “Color 2” phase). All of the heads/colors set for Phase 1 will illuminate
at the same time and flash opposite from all of the heads/colors set for Phase 2.
Prior to changing the Phase for any functions, please note the following limitations:
•
The Phase option is only programmable for the Flash Pattern functions.
It is not programmable for the directional functions (Left, Right, or
Center-Out).
•
There are 10 different Phase options
(shown in the chart below)
, allowing you to
customize which heads flash ON together and which are OFF together.
•
The Phase option is only compatible with Patterns 1-25. You cannot alter the
Phases for patterns 26-40 (the pre-set phase is crucial to the pattern).
1. Connect the RED wire to GROUND and the BLACK wire to GROUND.
2. Connect one of the function wires to +12VDC, to activate that function.
3. Place the light in
Phase Programming Mode
by holding the Pattern Select wire to
+12VDC
and releasing it after the unit flashes six times (~18 seconds - it will flash
once, twice, three times, four times, five times, then six times).
4. Scroll through the 10 optional Phase variations
(see chart below)
by touching and
releasing the Pattern Select wire to
GROUND
. The stick will display each
corresponding Phase pattern as you scroll to it.
Holding the Pattern Select wire to GROUND for 3 seconds (until it flashes once ) will
reset the Phase to the default setting.
5. If applicable, repeat Steps 2-4 to program the Phase setting for the other Function
wires.
6. Save your programming by holding the Pattern Select wire to
+12VDC
until the
unit flashes once (~3 seconds), then releasing it.
(Advanced Programming - Head Enable CONT’D)
Single Steady Head Programming
If you have programmed one of your function wires for the Single Steady Head
option (often used for California Title 13 compliance) as described on the page 8,
you can change which head is steady by following the Head Enable instructions on
the previous page for either color and the corresponding function wire. Each time
you scroll the head will advance one position to the right, then cycle back around.
-10-
NOTICE
Due to continuous product improvements, we must reserve the right to change any specifications and information,
contained in this manual at any time without notice. Star Headlight & Lantern Co., Inc. makes no warranty of any
kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein
or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual.
If you have any questions concerning this or any other product, please contact
our
Customer Service Department
at (585) 226-9787.
If a product must be returned for any reason, please contact our
Customer Service Department to obtain a Returned Materials Authorization
number (RMA #) before you ship the product back.
Please write the RMA # clearly on the package near the mailing label.
LED FIVE YEAR LIMITED WARRANTY
The manufacturer warrants this LED light against factory defects in material and workmanship for five
years after the date of purchase. The owner will be responsible for returning to the Service Center any
defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or
replace
at its option
, products, or part(s), which its inspection determines to be defective. Repaired or
replacement item(s) will be returned to the purchaser with transportation costs prepaid from the
service point. A copy of the purchaser's receipt must be returned with the defective item(s) in order to
qualify for the warranty coverage. Exclusions from this warranty include, but are not limited to, domes,
and/or the finish. This warranty shall not apply to any light, which has been altered, such that in the
manufacturer's judgment, the performance or reliability has been affected, or if any damage has
resulted from abnormal use or service.
There are no warranties expressed or implied (including any warranty of merchantability or fitness),
which extend this warranty period.
The loss of use of the product, loss of time, inconvenience,
commercial loss or consequential damages, including costs of any labor, are not covered
. The
manufacturer reserves the right to change the design of the product without assuming any obligation
to modify any product previously manufactured.
This warranty gives you specific legal rights. You might also have additional rights that may vary from
state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states
do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above
limitation(s) or exclusion(s) may not apply to you.
Important
: This product is used to
direct
traffic. Improper use may result in vehicular
collision, personal injury and/or death. Star Headlight & Lantern Co., Inc., and its
subsidiaries shall not be held responsible for damages directly or indirectly caused by
improper use of this product. Always carefully consider the effect on traffic that the
selected light pattern will have before engaging the lights.
Please Note:
These instructions are provided as a general guideline only. Specific
mounting and/or wiring, may be necessary and are the sole responsibility of the
installer. Star Headlight & Lantern Co., Inc. assumes no responsibility for the
integrity of the installation for this or any of its products.
