-3-
Standard Programming
•
Pattern Selection (both Warn and Traffic Directing Patterns)
•
Resetting the Factory defaults
Pattern Selection
1. Connect the RED wire to GROUND and the
BLACK wire to GROUND.
2. Activate the function you wish to program by
connecting the corresponding wire to
+12VDC.
3. Touch and release the Pattern Select wire to
+12VDC to scroll through the patterns shown
in the corresponding list.
Note: At any time you can shortcut to the
patterns with the asterisks by holding the
pattern select wire to +12VDC for the
indicated time.
4. Repeat for each function you wish to
program.
Warn Patterns
1 Flicker
*
(factory default)
2 Quadflash
†
3 Short Singleflash
†
4 Long Singleflash
5 Slow Doubleflash
†
6 Fast Doubleflash
†
7 Slow Tripleflash
†
8 Fast Tripleflash
†
9 Quintflash
†
10 Tripleflash w/Post Pop
†
11 Quadflash w/Post Pop
12 Quintflash w/Pre Pop
13 Doubleflash
14 Quadflash
15 Singleflash Flicker
16 Doubleflash Flicker
17 Single, Quad w/Post Pop, Flicker
18 Dual Color Single, Quad, Flicker
19 Dual Color Quad, Post Quint
20 Dual Color Flicker
21 Delta-Omega
22 Slowest Singleflash (-CON)
**
23 Slower Singleflash (-CON)
24 Slow Singleflash (-CON)
25 Fast Singleflash (-CON)
26 Random 1
◄
27 Random 2
◄
28 Random 3
◄
29 Flashing Bounce
◄
30 Full Bounce
◄
31 Split Bounce
◄
32 Half Bounce
◄
33 Bounce w/End Pop
◄
34 Search Lights
◄
35 Eyeballz
◄
36 Fade Invert
◄
37 Moving Out
◄
38 Triple In/Triple Out
◄
39 Two Speed
◄
40 Random 4
◄
*
Shortcut to Pattern #2 (3 sec/1 flash)
**
Shortcut to Pattern #15 (6 sec/2 flashes)
†
SAE Approved Pattern
◄
Single Color only, No Phase options
Patterns for Traffic Director
Left, Right, and Center Out functions
all use the same pattern
1 Standard
*
2 Standard with Constant End Flash
3 Standard with End Blink
4 Two-Head Traveling
5 Fast
†
6 Ultra-Fast
†
7 Four Head Traveling
†
8 Snake
†
9 Pop
10 Singleflash
†
**
(factory default)
* Shortcut to Pattern #1 (3 sec/1 flash)
** Shortcut to Pattern #10 (6 sec/2 flashes)
†
SAE Approved Pattern
Resetting To Factory Defaults
If you ever need to reset the entire light to the Factory Default Settings, follow the
steps below:
1. Connect only the RED wire to GROUND and the BLACK wire to GROUND.
2. Hold the Pattern Select wire (RED w/GREEN) to
+12VDC
until the unit flashes once
(~3 seconds).
-4-
•
Alternate Wire Setups
•
Custom Wire Programming
•
Priority Modification
•
Head Enable (which heads activate)
•
Single Steady Head Programming
•
Phase Selection (which heads alternate from one another)
For Advanced Programming options and warranty information, please review the
full manual on our website at www.star1889.com.
Please be aware that the Quick Stick is
designed with two internal connectors on the
harness that can be accessed by removing
the two screws securing the endcap and
harness. This allows a Quick Stick that needs
service to be removed from the vehicle
without needing to remove the entire harness.
If you do use this feature,
it is
imperative
that the zip tie securing the connection be
replaced upon reinstallation to ensure that a good connection is maintained.
Because the connectors are inside the light stick, extra care must be taken so that
they are reinstalled properly. The installer is fully responsible for any issues that may
occur as a result of using the disconnect feature. This includes loose connections
and pinched wires.
Operation
Using your user supplied switches, 12VDC to the wires indicated in the wiring
diagram on page 2 to activate the desired function.
Please note the following:
•
The RED wire MUST have +12VDC applied to it for any of the patterns to work.
•
Higher priority wires will override the patterns on any lower priority wires for the
heads that are enabled.
HIGHEST PRIORITY
LOWEST PRIORITY
Pink > White w/Brown > Green w/Yellow > Orange w/Red > Yellow
•
Activating the Right and Left patterns together will produce the Center-Out
Pattern.
Service
Removing the Quick Stick From the Harness
Advanced Programming Options
