Stanley STC24, Инструкция по эксплуатации

Страница: 16 / 18

16 • ENGLISH
f
Please check that the air consumption and the
maximum working pressure of the pneumatic tool
to be used are compatible with the pressure set
on the pressure regulator and with the amount of air
supplied by the compressor.
f
Always pull out the plug and drain the receiver once
you have completed your work (Fig. 10 - 11).
5. MAINTENANCE
f
Before carrying out any operation, always pull out
the plug and drain the receiver completely (Fig. 10 - 11).
f
Check that all screws (in particular those of the head
of the unit) are tightly drawn up (torque 10 Nm =
1.02 Kgm). The control must be performed before the
first start-up of the compressor and subsequently before
the first intensive use in order to restore
the correct closing torque value modified as a result
of heat expansion.
f
After loosening any safety screws, clean the intake
filter according to the type of working environment
and at least every 100 hours (Fig. 12). If necessary,
replace the filter element (clogging of the filter
reduces compressor performance and an inefficient
filter causes increased wear).
f
Replace the oil after the first 100 hours of operation
and every 300 hours subsequently (Fig. 13).
Remember to check the oil level at regular intervals. Use
SAE 40. (For cold climates, SAE 20 is recommended).
Never mix different grade oils. If the oil changes color
(whitish = presence of water; dark = overheated), it is
good practice to replace the oil immediately.
f
Periodically (or after working with the compressor for
more than an hour), drain the condensate that forms
inside the receiver (Fig. 11) due to the humidity in the air.
This protects the receiver from corrosion and does not
restrict its capacity.
f
Spent oil (lubricated models) and condensate MUST BE
DISPOSED OF in accordance with environmental
protection regulations and current legislation.
The compressor must be disposed in conformity with
the methods provided for by local regulations.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
LUBRICATION
Your power tool requires no additional lubrication.
CLEANING
Warning! Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
ACCESSORIES
Recommended accessories for use with your tool are available at
extra cost from your local dealer or authorized service center.
Warning! The use of any accessory not recommended
for use with this tool could be hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
STANLEY offers a full network of company-owned and
authorized service locations. All STANLEY Service Centers
are staffed with trained personnel to provide customers with
efficient and reliable power tool service. For more information
about our authorized service centers and if you need technical
advice, repair, or genuine factory replacement parts, contact
the STANLEY location nearest you.
TABLE 1 – MAINTENANCE
FUNCTION
AFTER THE
FIRST 100
HOURS
EVERY 100
HOURS
EVERY 300
HOURS
Cleaning of intake filter
and/or substitution of
filtering element
●
Change of oil
● ●
Tightening of head
tension rods
At start-up and after the first hour of work
Draining tank
condensate
Periodically and at the end of work