Stanley 79-004 Скачать руководство пользователя

Страница: 7 / 16

Carefully clean both the rubber disk (B) and its seat.

Refit all parts accurately.

Air losses

This can be caused by under tightening of a union
-

check all unions, wetting them with soapy water.

Compressor turns but does not load

(fig.18)

This may be due to failure of the valves (C1 - C2) or of a seal (B1 -
B2): replace the damaged part.

Compressor not starting

If the compressor has trouble starting, check the following:
-

Does mains power match that of the data-plate?

Are power cable extensions of adequate diameter or length?

Is the work environment too cold (under 0°C)?

Was the thermal-breaker tripped?

Is there enough oil in the housing to ensure lubrication?

Is power supplied to the electrical line? (sockets well connected,
thermal-breaker, fuses in good condition).

- 7-

Compressor not stopping

- If the compressor does not stop when maximum pressure is

reached, the tank safety valve comes into operation. To repair the
valve, contact your nearest service centre.

IMPORTANT

Do not on any account unscrew any connection while the tank is
pressurised

always check that the tank is pressure free.

Do not drill holes, weld or purposely deform the compressed air
tank.

Do not perform any maintenance on the compressor unless you
have disconnected the power plug.

Temperature in operating ambient: 0°C +35°C.

Do not aim jets of water or flammable liquids on the compressor.

Do not place flammable objects near the compressor.

During down-times, turn the pressure switch to “0” position (OFF).

Never aim the air jet at people or animals

Do not transport the compressor while the tank is pressurised.

Take came, as some parts of the compressor, such as the head
and delivery tubes, as they can reach high temperatures. Do not
touch these parts to avoid burns.(fig. 8-9)

Transport the compressor, lifting or pulling it with the appropriate
grips or handles

Keep children and animals well away from the machine operating
area.

If using the compressor for painting:

a) Do not work in closed environments or near to naked flames

b) Make sure there is adequate ventilation at the place of work

c) Protect your nose and mouth with an appropriate mask.

If the electrical cable or plug are damaged, do not use the com-
pressor and contact an authorised service centre to replace the
faulty component with an original spare part.

If the compressor is located on a shelf above floor height, it must
be secured to prevent it falling while in operation.

Do not put objects or your hands inside the protective grilles to
avoid injury to yourself or damage to the compressor. (Do not use
the compressor as a blunt object toward things or animals, to avoid
serious damage).

When you have finished using the compressor, always remove the
plug from the power socket.

Maximum operating pressure 8.5 bar
Minimum operating pressure 8 bar

Acoustic pressure measured free-field at a distance of 4 m ±3 dB(A) at
maximum operating pressure.

RPM

dB(A)

Model Nr. 79-004

2850 75

The level of acoustic pressure can increase from 1 to 10 dB(A) accord-
ing to the place in which the compressor is installed.

HINTS FOR EFFICIENT OPERATION

For efficient operation of the machine at full continuing load and at
maximum operating pressure, make sure the temperature of the
work environment indoors does not exceed 25°C.

We advise you to use the compressor at 70% maximum duty per
hour at full load as this ensures efficient operation of the product
long-term.

STORING THE PACKED AND UNPACKED COMPRESSOR

For the whole time that the compressor is not used before unpacking
store in a dry place at a temperature between 5°C and 45°C and shel-
tered away from weather. For the whole time that the compressor is
not used after unpacking, while waiting to start it up or due to produc-
tion stoppages, place sheets over it to protect from dust, which may
settle on the components. The oil is to be replaced and the operational
efficiency of the compressor is to be checked if it is not used for long
periods.

PNEUMATIC CONNECTIONS

Make sure you always use pneumatic tubes for compressed air with
maximum pressure characteristics that are adequate for the compres-
sor.Do not attempt to repair tubes if faulty.

WE RESERVE THE RIGHT TO MAKE ANY MODIFICATIONS

WITHOUT PRIOR NOTICE WHENEVER NECESSARY.