Stanley 309311x692A Скачать руководство пользователя страница 22

Страница: 22 / 64

F–030601L

WARNING: Before you make an in-

spection, adjustment, or repair to

the unit, disconnect the wire to the

spark plug. Remove the spark plug wire to

prevent the engine from starting by acci-

dent

1. Make sure the unit is on a hard flat surface.
2. Check the air pressure in the tires. If the air

pressure is incorrect, the mower housing will

not cut level. Make sure the tires are inflated

to: Front Tires 1.5 BAR (22 PSI), Rear Tires

1 BAR (14 PSI).

3. Open the

cover (5).

(Figure 18)

Move the

lift lever (1)

to the

LEVEL ADJUSTMENT position

(2)

(Figure 18 and 19)

Loosen the front and rear

adjuster knobs (4)

. Make sure both sides of

the mower housing are setting on a flat sur-

face. Also, make sure the lift links and adjust-

er plates are loose and can easily move up

or down.

6. Tighten the front and rear

adjuster knobs

(4)

. Make sure the

adjuster knobs (4)

are

tight. If necessary, use a wrench to tighten

the

adjuster knobs (4).

For plastic

adjuster

knobs (4),

tighten to a torque of 7 foot

pounds (9,5 N–m). For metal

adjuster

knobs (4),

tighten to a torque of 10 foot

pounds (13,5 N–m).

(Figure 20)

Raise the

lift lever (1)

from the

LEVEL ADJUSTMENT position (2)

to a

CUTTING HEIGHT position (3).

8. Close the

cover (5).

9. Mow for a short distance. If the height of cut

is not level, repeat the above steps.

CAUTION: Do not operate with the mower

housing in the LEVEL ADJUSTMENT posi-

tion (2). If you operate in the LEVEL ADJUST-

MENT position (2), the mower housing and

blade will be damaged.

Where To Lubricate

(Figure 21)

Lubricate the areas shown
with engine oil.

Apply grease with a brush to
the areas shown.

Models with grease fittings:
Lubricate with grease gun.

NOTE: Apply grease to the steering gear as-

sembly.
CAUTION: If the unit is operated in dry areas

that have sand, use a dry graphite spray to

lubricate the unit.

Check The Tires

Check the air pressure in the tires. Tires with too

much air pressure will cause the unit to ride

rough. Also, the wrong air pressure will keep the

mower housing from cutting level. The correct

air pressure is: Front Tires 1.5 BAR (22 PSI),

Rear Tires 1 BAR (14 PSI).

How To Replace The Motion Drive Belts

(Figure 22)

Engine Drive Belt Removal

1. Remove the mower housing. See the instruc-

tions on “How To Remove The Mower Hous-

ing”.

(Figure 22)

Remove the

engine drive belt

(3)

from the

idler pulley (1)

. If necessary,

remove the

idler pulley (1)

3. Remove the

engine drive belt (3)

from the

variator pulley (4)

. If necessary, loosen the

belt guides (5)

at the

variator pulley (4)

4. Remove the

engine drive belt (3)

from the

stack pulley (2).

NOTE: Because of the width of the engine

drive belt (3), the belt must be twisted and

then pulled downward to slip between the

stack pulley (2) and the belt guides (5).

Engine Drive Belt Installation

1. To install the

engine drive belt (3)

, reverse

the above steps.

(Figure 22)

Make sure that the

engine drive

belt (3)

is installed correctly and is inside of

all the

belt guides (5)

3. Make sure that the fasteners for the

belt

guides (5)

are tight.

4. Install the mower housing. See the instruc-

tions on “How To Install The Mower Hous-

ing”.

Transaxle Drive Belt Removal

1. Remove the mower housing. See the instruc-

tions on “How To Remove The Mower Hous-

ing”.

2. Remove the engine drive belt. See “Engine

Drive Belt Removal”.

3. The rear of the unit must be supported with

the rear wheels off of the ground so that the

transaxle can be lowered. Set the rear of the

unit on jackstands or a similar type of sup-

port. Do not set the transaxle on the jack-

stands; set the frame on the jackstands.

(Figure 15)

Remove the

hair pin (1)

and

washer (4)

from the

adjustable nut (2)

. Re-

move the

adjustable nut (2)

from the

shift

yoke (3)

(Figure 22)

Remove the carriage bolt from

the

torque strap (4)

6. To relieve tension on the

transaxle drive

belt (6)

, depress the clutch/brake pedal and

set the parking brake.

(Figure 23)

Remove the

transaxle drive

belt (6)

from the

transaxle idler pulley (7)

8. Remove the

transaxle drive belt (6)

from

the

variator pulley (8)

(Figure 22)

Loosen the

mounting bolts (9)

on the left side of the

transaxle (10)

. Loosen

until the mounting nuts are at the end of the

mounting bolts (9)

10.Remove the

mounting bolt (11)

from the

right side of the

transaxle (10)

. This will

allow the right side of the

transaxle (10)

drop down and provide clearance for the

transaxle drive belt (6)

Transaxle Drive Belt Installation

1. To install the

transaxle drive belt (6)

, re-

verse the above steps.

(Figure 23)

Make sure that the

transaxle

drive belt (6)

is installed correctly and is in-

side of all the

belt guides (12)

3. Make sure that all fasteners, all the mounting

bolts, and all the

belt guides (12)

are tight.

4. Install the engine drive belt. See “Engine

Drive Belt Installation”.

5. Install the mower housing. See the instruc-

tions on “How To Install The Mower Hous-

ing”.

6. Check the operation of the drive system. See

“How To Check And Adjust The Clutch” and

also “How To Adjust The Speed Control

Pedal”.

How To Replace The Mower Drive Belt

(Figure 14)

1. Remove the mower housing. See the instruc-

tions on “How To Remove The Mower Hous-

ing”.

2. Pull the

belt retainer (1)

away from the

idler

pulley (2)

and remove the

mower drive belt

(3).

3. Pull the

brake pad (7)

away from the

jack-

shaft pulley (4)

and remove the

mower

drive belt (3).
NOTE: Replace the mower drive belt (3)

with an original equipment belt from an

authorized service center.

4. A correct replacement part or assistance is

available from an Authorized Service Center

in your area.

5. To install the motion drive belt, reverse the

above steps.

6. Install the mower housing. See the instruc-

tions on “How To Install The Mower Hous-

ing”.

7. Before you mow, check the blade rotation

control. See the instructions on “How To Ad-

just The Blade Rotation Control”.

How To Remove The Mower Housing

(Figure 6)

Move the

blade rotation control

(1)

to the

DISENGAGE position (8).

(Figure 18)

Move the

lift lever (1)

to the

LEVEL ADJUSTMENT position (2)

NOTE: Make sure the lift lever (1) is

locked in the LEVEL ADJUSTMENT posi-

tion (2).

(Figure 27)

Remove the hair pins and the

washers from the

rear suspension arms

(3)

. See illustrations “C” and “D”.

4. Remove the hair pins and washers from the

suspension links (4)

. See illustrations “A”

and “B”.

5. Disconnect the

extension spring (5)

from

the

blade control rod (6)

. See illustration

“E”.

6. Disconnect the

front hanger (9)

from the

frame support. See illustration “F”.

7. Remove the

mower drive belt (7)

from the

stack pulley (8).

See illustration “G”.

8. Pull the mower housing away from the right

side of the unit.

Содержание 309311x692A

































































Результаты поиска

Содержание 309311x692A

Отзывы:

Похожие инструкции для 309311x692A

Бренды по названию

Популярные бренды

Stanley 309311x692A, Инструкция

Результаты поиска

Содержание 309311x692A

Отзывы:

Похожие инструкции для 309311x692A

Бренды по названию

Популярные бренды