background image

29

Maintenance schedule

Maintenance schedule

Daily

General inspection genset and engine room

Check air filter indicator (change filter if necessary)

Drain charge air cooler (make sure drain hole is not clogged)

Check lubrication oil level

Check coolant level

Check fuel oil level

Check/drain fuel pre-filter/water separator ............................................... (refer to note 1)

Drain water from fuel tank

Daily operation records

Weekly

Check starting batteries; electrolyte level/load

Check electrical system for loose terminals/contacts, remove dirt/oxides

Check foundation bolts

Check lubrication oil for abnormal smell or waterdilution

Check settings of valves and operate valves to keep them movable

After first 10 operating hours

Check lubrication oil level

Check coolant level

After first 150 operating hours

Check/adjust drive belts

Check/adjust valve clearances

Every 125-500 operating hours or every 12 months

Change lubrication oil .............................................................................. (refer to note 3)

Change lubrication oil filters .................................................................... (refer to note 4)

1)

 Check the manometer(valid only for twin filters) and change filter if necessary.

2)

 To be carried out at an authorized Volvo Penta workshop.

3)

Oil change intervals vary, depending on oil grade and sulphur content of the fuel. Refer to chapter
”Technical Data Lubrication oil specification”

4)

Change oil filters every second oil change.

Содержание D5A T







































































Отзывы: