manualshive.com logo in svg

Stamford D5A T, Руководство оператора

Поделиться
Скачать
Stamford D5A T Скачать руководство пользователя страница 17

17

Presentation

D5A TA KC (2-circuit)

The D5A TA KC is a turbocharged, aftercooled, in-line, direct injection, 4-cylinder, 4-stroke marine genset. It is fit-
ted with  connections for 2-circuit keel cooling.

An optimal combination of combustion chambers, fuel injection system, effective turbocharger and charge air
cooling, provide excellent fuel consumption over the whole range of power output.

The engine is mounted on a frame with a Stamford single or double bearing marine generator. Different starting
and control systems are available.

D5A TA Genset

1. Air outlet generator

2. Governor & Stop solenoid

3. Electrical connection box

4. Fuel return

5. Oil cooler

6. HT-pump

7. Fuel pump & Fuel inlet

8. Lifting eyes

9. Vibration damper

10. Fuel filter

11. Oil filter

12. Oil dip stick

13. LT-pump

14. Coolingwater inlet (LT-circuit)

15. Electrical connection unit

16. Air inlet generator

17. Coolingwater inlet (HT-circuit)

18. Cooling water outlet (LT-circuit)

19. Charge air cooler

20. Exhaust manifold

21. Air filter

22. Air filter indicator

23. Turbocharger

24. Flexible mountings

25. Electrical starter

26. Engine oil drain pump

27. Alternator

28. Cooling water outlet (HT-circuit)

Содержание D5A T







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды