Stahl SLE22 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 29

Stahl SLE22 Скачать руководство пользователя страница 25

9

Decommissioning

10.2013

25

B

A

_S

LE

22

_E

N

.D

O

C

X

9

Decommissioning

Decommissioning the system or the

SLE22

must be carried out by the user in accor-

dance with §20 BImSchG (Federal Immission Control Act). If the user does not comply,
the authority responsible must prohibit operation in full or partially until the requirement,
court order or obligations from the statutory regulation acc. to §7 has been met.

When replacing the SLE22 every non-essential downtime or interference with
operations must be avoided.

Replacement and recommissioning the

SLE22

must be performed by a

qualified person

(See Chapter 4.4., Replacement of device and sensor).

Disposal of the device must comply with national environmental laws.

In Germany this is the "Electrical and electronic device law" of 16 March 2005 (BGB. I
page 762), last amended by Art. 2, Clause 1 of the Law of 16 November 2011 (BGBI. I
page 2224).
The requirements of Directive 98/34/EC, amended by Directive 98/48/EC of the Euro-
pean Parliament and the Commission of 20 July 1998 (ABl. EC No. L 217 page 18) have
been met.

The device must be returned to the manufacturer for disposal.

No batteries or rechargeable batteries are installed in the

SLE22

.

«
...
23
24
25
26
27
...
»

Содержание SLE22






























Отзывы:

Нет отзывов