Stahl 8146/1 Скачать руководство пользователя

Страница: 18 / 27

Mounting and Installation

137189 / 8146619300

2016-11-10·BA00·III·en·06

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

Terminal Boxes

Series 8146/1, Series 8146/2

6.2

Installation

6.2.1 Conductor Connection



Select suitable conductors that do not exceed the permitted heating temperature within the

enclosure.



Ensure that conductors have the specified cross-sections.



Guide the conductor insulation so that it reaches the terminals.



Do not damage the conductor when stripping the insulation (e.g. by denting it).



Attach the core end sleeves properly.



If the system is equipped with all possible terminals and live conductors, and and the

maximum current load has been reached, ensure that the length of a conductor from the

screw connection to the terminal point does not exceed the diagonal planes of the

enclosure.

Operation under difficult conditions, such as on ships or in strong sunlight, requires

additional measures to be taken for correct installation, depending on the place of use.

Further information and instructions on this can be obtained from your regional sales

contact on request.

DANGER! Explosion due to excess heating inside the enclosure!

Non-compliance results in fatal or severe injuries.



Ensure that distances between Ex e electric circuits and Ex i electric circuits comply

with standards (EN IEC 60079-11).



Select suitable conductors that do not exceed the permitted heating temperature

within the enclosure.



Pay attention to the specified cross-sections.



Attach the core end sleeves properly.

DANGER! Explosion due to improper installation!

Non-compliance results in fatal or severe injuries.



Install the device carefully and only in accordance with the safety notes

("Safety" section).



The installation steps stated below must be carried out very precisely.

The necessary technical details/data on electric installation can be found in the following

documents:



"Technical data" chapter in these operating instructions



Documentation and data sheets provided by the terminal manufacturers



Documentation and data sheets of the installed devices (e.g. for specifications on

equipotential bonding, earthing and intrinsically safe circuits)

Содержание 8146/1




























Результаты поиска

Содержание 8146/1

Отзывы:

Похожие инструкции для 8146/1

Бренды по названию

Популярные бренды

Stahl 8146/1, Руководство по эксплуатации

Результаты поиска

Содержание 8146/1

Отзывы:

Похожие инструкции для 8146/1

Бренды по названию

Популярные бренды