SSI PRL-1600 Скачать руководство пользователя страница 9

SOLID STATE INSTRUMENTS

INSTRUCTION SHEET

PRT-16 BASE UNIT

Setting the System CHANNEL

 - Each system -- the Transmitter and

Receiver -- must operate on one of six different channels.  A
"channel" is a collection of 50 specific frequencies that are arranged
in a specific "hop sequence".   A unique channel allows multiple
systems to operate in the same radio airspace without any
interference with each other.  Therefore, the transmitter and receiver
must have the same channel setting. The channel address is set
using a 3-bit binary code.  See 

Table 1

 at right for complete list of the

channels.  Note that Channel #6 is the highest channel number and
even though there are eight unique switch combinations, Channel 6 is
the highest channel that can be selected. The last three switch
combinations all result in Channel #6 being selected.

Switch #4

 - Not used.

Switch #5

 - Not used.

Switch #6 

-

 

Not used

Switch #7 - Setting the Transmitter Input Mode - 

The PRL-1600

can operate in the Form C or Form A modes.  In the Form C (3-Wire)
mode, each input channel uses the K, Y and Z inputs. Two
independent 3-Wire meter pulse channels can be transmitted.  In the
Form A (2-Wire) mode, each pulse channel uses the K (common)
and a Y input.  Four independent 2-Wire meter pulse channels can
be transmitted.  Set 

Switch #7

 to the 

DOWN

 position for the Form A

mode and 

UP

 for Form C mode.

Switch #8 - Pairing the Transmitter and Receiver - 

The PRT-1600

System requires that each Transmitter and Receiver are paired
together.  Each Transmitter must learn the address of the Receiver it
is designated to talk to.  This makes it possible for the Transmitter to
only talk to the designated Receiver and ignore other devices sending
and receiving information on a particular frequency. After installation
is complete, perform the pairing procedure described on page 15
ONLY IF the system has not been previously paired at the factory.

***Do not switch #8 UP if the system is already paired.***

a division of Brayden Automation Corp.

6230 Aviation Circle, Loveland, Colorado 80538

Phone: (970)461-9600

E-mail: [email protected]

Revision: 4/10/22

9

CHANNEL#

1
2
3
4
5
6
6
6

DN
DN
DN

DN
UP
DN

TABLE 1

SW#1 SW#2 SW#3

DN
DN
UP

DN
UP

UP
DN

UP
DN

UP

UP

DN

UP

DN

UP

UP

UP

UP

Input Mode

DN
UP

TABLE 2

SW#7

FORM C (3W)

FORM A (2W)

Mode

DN

DN

SW#4 SW#5 SW#6

DN

DEFAULT

TABLE 3

Run/Learn

DN
UP

SW#8

LEARN

RUN

TABLE 4

PRT-16

Transmitter

Base Unit

1

2

3

4

5

6

7

8

9

2 3 4 5 6 7 8

1

4

CHAN#

2

1

Dip Switch DS1

Lear

n

Set XMTR

channel #

Dip Switches #4 - #7
are specific to the
Transmitter. See
below.

Learn
Mode

Enable

CONTROL

 C

A

B

L

E

Содержание PRL-1600
























Отзывы: