background image

 

24 

 © SprayTECH.  All rights reserved. 

SprayTECH

1770 Fernbrook Lane
Minneapolis, MN  55447

Technical Assistance/

Order Entry:

Fax - Technical Assistance:

Fax - Order Entry:

1-800-526-5362

1-800-525-9501

1-800-528-4826

www.spraytechinc.com

 Limited Warranty

SprayTECH Corporation, (“SprayTECH”) warrants that at the time of delivery to the original purchaser for use (“End User”), the 

equipment covered by this warranty is free from defects in material and workmanship.  With the exception of any special, limited, or 

extended warranty published by SprayTECH, SprayTECH’s obligation under this warranty is limited to replacing or repairing without 

charge those parts which, to SprayTECH’s reasonable satisfaction, are shown to be defective within twelve (12) months after sale to the 

End User.  This warranty applies only when the unit is installed and operated in accordance with the recommendations and instructions 

of SprayTECH.
This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident, faulty 

installation, substitution of non-SprayTECH component parts, or tampering with the unit in a manner to impair normal operation.
Defective parts are to be returned to an authorized SprayTECH sales/service outlet.  All transportation charges, including return to the 

factory, if necessary, are to be borne and prepaid by the End User.  Repaired or replaced equipment will be returned to the End User 

transportation prepaid.
THERE IS NO OTHER EXPRESS WARRANTY.  SPRAYTECH HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES 

INCLUDING, BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE 

EXTENT PERMITTED BY LAW.  THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED 

TO THE TIME PERIOD SPECIFIED IN THE EXPRESS WARRANTY.  IN NO CASE SHALL SPRAYTECH LIABILITY EXCEED THE 

AMOUNT OF THE PURCHASE PRICE.  LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES UNDER ANY 

AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.
SPRAYTECH MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS 

FOR A PARTICULAR PURPOSE WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT 

NOT MANUFACTURED BY SPRAYTECH.  THOSE ITEMS SOLD, BUT NOT MANUFACTURED BY SPRAYTECH (SUCH AS GAS 

ENGINES, SWITCHES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF THEIR MANUFACTURER.  SPRAYTECH 

WILL PROVIDE THE PURCHASER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM FOR BREACH OF THESE 

WARRANTIES.

Patents

These products are covered by one or more of the following U.S. patents:

 

6,031,352 

5,848,566 

5,769,321 

5,725,364 

5,671,656 

5,435,697 

5,228,842

 

5,346,037 

5,252,210 

5,217,238 

5,192,425 

4,908,538 

4,768,929 

4,744,571

 

D384,676 

6,179,222 

5,934,883 

4,723,892

Material Safety Data Sheets (MSDS) are available on SprayTECH’s website or by calling Technical Service.

Содержание 0552061

























Отзывы: