background image

Step 5: Connecting the Assembled

Ladder with the Outside Legs

1. Put the plastic plugs into the holes on the bottom of the curved ends of the Vertical Supports.  2. Insert the two
Vertical Supports into the Top Ladder Handles. (The curved Vertical Support ends should be facing the Interior
Steps.)  3. Line up the holes for the Metal Screws.  4. Using the Ladder Tool, tighten the Metal Screws with the
corresponding Nuts and Washers.  5. The outside Vertical Supports are now attached.

1

2

3

4

5

Step 6:  Connecting the Assembled Ladders

1. Place the SplashLadder’s Exterior Steps on the outside of the Vertical Supports. (Be sure the Exterior Steps
slope down and away from the pool.)  2. Line up the holes of the Platform piece and the Exterior Steps for the
Metal Screws.  3. Using the Ladder Tool, tighten the Metal Screws with the corresponding Nuts and Washers.
4. The SplashLadder assembly is now complete.

5

©

2003-Splash Superpools Ltd.

Parts Needed:

Assembled Inside Steps
Assembled Outside Steps
N. (2) Metal Screws

1

2

3

4

N

Parts Needed:

Assembled Interior Steps
G. (2) Vertical Supports
M. (2) Plastic Plugs
N. (2) Metal Screws with Nuts and Washers

M

N

G

Содержание TitanPool3



























Отзывы: