9
ASSEMBLY
Assembly
■
UNPACKING THE UNIT
1. Cut the straps then lift the carton off.
2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged
parts are found, or parts are missing, contact your dealer immediately.
3. Locate the hardware package. The hardware is separated into four steps. Remove the tools first.
Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing, for reference.
STEP 1: REAR STABILIZER ASSEMBLY
1. Install the Rear Stabilizer (5) onto the Main Frame (1) with the 4pcs of 3/8” x 2-1/4” Hex Head
Screws (50) and 4pcs of 3/8”x 25 x 2T Flat Washers (71) by using the 12/14mm Wrench (100).
STEP 2: FRONT CONSOLE MAST ASSEMBLY
1. Unravel the Computer Cable (29) and snake it through the Console Mast Cover (38) and the
Console Mast (2) until the cable connector comes out the top opening of the console mast. Slide
the plastic cover (38) onto the console mast, ensuring the correct orientation of the cover.
2. Install the Console Mast (2) onto the Main Frame (1) with the 7pcs of 5/16” x 5/8” Hex Head
Screws (51), 6pcs of 5/16”x19x1.5T Flat Washers (72) on the side screws and 1pc of 5/16” x 20x
1.5T Curved Washer (99) on the front screw by using the 12/14mm Wrench (100).
STEP 3: HANDLE BAR ASSEMBLY
1.
Install the Handle Bar (3) onto the Front Console Mast (2) with the 2pcs of 5/16” x 5/8” Hex Head
Screws (51), 2pcs of 5/16” x 19 x 1.5T Flat Washers (72) and 2pcs of 8m/m Split Washers (103)
by using the 12/14mm Wrench (100).
STEP 4: CONSOLE AND PLASTIC PARTS ASSEMBLY
1.
Insert the Computer Cable (29) and Handlepulse W/Cables (26) onto the Console (34).
2.
Secure the Console (34) onto the Front Console Mast (2) with the 4pcs of M5
×
12mm Phillips
Head Screws (58) by using the Phillips Head Screw Driver (93).
3.
Secure the Front Stabilizer Cover (40) and the Rear Stabilizer Cover (41) onto the Main Frame (1)
with the 4pcs of M5
×
12mm Phillips Head Screws (58) by using the Phillips Head Screw Driver
(93).
4.
Install the Pedal (L&R) (45&46) onto the Crank (L&R) (16L&16R) by using the13/15mm
Wrench (92).
5.
Turn on the Locking Knob (106) and install the Inner Slide Assembly (6) into the Outer Slide.
6.
Adjust the highly and tighten the Locking Knob (106).
7.
Turn on the Fore Aft Adjustment Knob (86) and install the Seat Slide Bracket (7) put on the Inner
Slide Assembly (6).
8.
Adjust the position and tighten the Fore Aft Adjustment Knob (86).
9.
Install the Seat Bottom Cushion (19) on the Seat Slide Bracket (7) by using the 12/14mm Wrench
(100).
Содержание XU875-A27
