Spirax Sarco FTC80 Скачать руководство пользователя

Страница: 22 / 24

IM-IBR16-32IN

Issue 1

7. Spare parts

The spare parts available are shown in solid outline. Parts shown in broken line are not

supplied as spares. Spares do not come packaged with cover gasket (

). In order to offer the

maximum flexibility in choice, cover gasket (

) needs to be ordered separately.

Available spares

Mechanism maintenance kit including float

3, 13, 18a,18b, 19

Seat and ball head

3, 15, 16, 17, 19, 26

Cover gasket (3 off)

Strainer screen

8, 9

Strainer gasket (3 off)

Mechanism including float.

3, 13, 18a, 18b, 19

How to order spares

Always order spares by using the description given in the column headed 'Available spares'

and state the size and type of trap, including pressure range.

How to order example:

1 off Seat and ball head set for a Spirax Sarco DN40 FTC80-45

ball float steam trap.

Содержание FTC80

























Результаты поиска

Содержание FTC80

Отзывы:

Похожие инструкции для FTC80

Бренды по названию

Популярные бренды

Spirax Sarco FTC80, Инструкция по установке и обслуживанию

Результаты поиска

Содержание FTC80

Отзывы:

Похожие инструкции для FTC80

Бренды по названию

Популярные бренды