SPIDER CROSS LINER Скачать руководство пользователя страница 54

Страница: 54 / 62

Operator’s Manual – Spider CROSS LINER

54 / 62

DRIVE BELTS AND STEERING CHAINS

INSPECTION

1) Place the mower on a flat and firm surface, press CENTRAL STOP on both the controller and the mower

and remove the key

2) Remove the engine cover and the side covers (4x screw - use a 17 mm socket with an extension).

3) Check the chain tension by applying a slight thumb pressure in the middle of the branch. Deflection should

be within 2 cm.

4) Inspect both wings.

TENSIONING



DRIVE BELT

Tensioning is carried out with the belt tensioner (Loosen the nut, tension the belt and again tighten the nut.)



STEERING CHAIN

Tensioning is carried out with the chain tensioner.

TIP: For better access to belt and chain tensioner on the left, unlock the tank strap and tilt the tank. Carry out
maintenance on the belt and fasten the tank properly back in place. Make sure that no fuel leaks when handling the
tank.



TRACTION DRIVE BELT

These are maintenance-free belts, in case of excessive tension, have the belt replaced by an authorized service
center.

EXCHANGE

Damaged and worn chains / belts must be replaced immediately. Have the replacement carried out by an authorized
service center.

Obrázek 7 – Pohonné prvky

Obrázek 8 – Pohonné prvky

STEERING CHAIN

BELT TENSIONER

CHAIN TENSIONER

DRIVE BELTS

Содержание CROSS LINER































































Результаты поиска

Содержание CROSS LINER

Отзывы:

Похожие инструкции для CROSS LINER

Бренды по названию

Популярные бренды

SPIDER CROSS LINER, Руководство оператора

Результаты поиска

Содержание CROSS LINER

Отзывы:

Похожие инструкции для CROSS LINER

Бренды по названию

Популярные бренды