Speeflo PowrTwin 6900 Plus, Руководство пользователя

Страница: 34 / 36

34 © Titan Tool Inc. All rights reserved.
SaE O-Ring Fitting Installation
Steps 1 & 2:
Step 3:
Step 4:
Step 5:
Cautions:
Lubricate
Lubricate
Tighten nut
Recess
gap
No gap
Align
Hold
this part
stationay
Avoid screwing fitting in too far.
Avoid leaving fitting too far out.
Bent washer allows
for o-ring extrusion
O-ring cut on
thread
1. Pull washer and
o-ring back as far as
possible.
2. Lubricate o-ring and
entrance port.
3. Screw fitting in until
washer pushes o-ring
into entrance and sits
flat against port. (Do
not tighten! - only do
this step hand tight to
compress o-ring into
port!)
4. Back fitting out
no more than one
complete turn to align
as required.
5. Torque nut wrench
tight holding backup
on fitting. This should
expose a recess
gap behind the nut
which can act as an
indicator that the
fitting is assembled
correctly. (This is a
feature for a specific
version of this fitting
only - which screws
into the cylinder head.
Other fittings, as the
ones which attach to
the hydraulic pump,
assemble the same
but may not have the
indicator.)
accessories and Service Kits
These items may be purchased separately from your local Titan
distributor.
Part No. Description
103-816 5 Gal. Siphon Hose Assembly w/Rock
Catcher 1” x 4.5’
103-817 55 Gal. Siphon Hose Assembly w/Rock
Catcher 1” x 6.5’
103-627 Rock Catcher
930-004 Paint Filter Element, 0 Mesh (for mastics)
930-005 Paint Filter Element, 5 Mesh (for
multicolors and heavy materials)
930-006 Paint Filter Element, 50 Mesh (for latex
and normal architectural materials)
930-007 Paint Filter Elements, 100 Mesh (for
stains, lacquers and fine materials)
520-050 SGX-20 G, T, and 1/4” Hose Kit
520-051 SGX-20 G, T, and 3/8” Hose Kit
101-208 Grounding Clamp
101-212 Grounding Wire, 12 Gauge x 25’
314-480 Piston Lube
430-362 Coolflo™ Hydraulic Fluid, 1 Quart
430-361 Coolflo™ Hydraulic Fluid, 1 Gallon
975-212 2-Gun Manifold with Ball Valves, 1/4”
975-213 3-Gun Manifold with Ball Valves, 1/4”
975-312 2-Gun Manifold with Ball Valves, 3/8”
975-313 3-Gun Manifold with Ball Valves, 3/8”
808-550 3/8” NPS(M) x 3” hex fitting
airless Tip Selection
Tips are selected by the orifice size and fan width. The proper
selection is determined by the fan width required for a specific job
and by the orifice size that will supply the desired amount of fluid
and accomplish proper atomization.
For light viscosity fluids, smaller orifice tips generally are desired.
For heavier viscosity materials, larger orifice tips are preferred.
Please refer to the chart below.
NOTE: Do not exceed the pump’s recommended tip size.
The following chart indicates the most common sizes and the
appropriate materials to be sprayed.
Tip Size Spray Material Filter Type
.011 – .013 Laquers and stains 100 mesh filter
.015 – .019 Oil and latex 50 mesh filter
.021 – .026 Heavy bodied latex and blockfillers 5 mesh filter
Fan widths measuring 8” to 12” (20 to 30 cm) are most preferred
because they offer more control while spraying and are less likely
to plug.