SpeedEPart LST42H Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

background image

16

FIGURE 33

RIGHT SIDE VIEW

FIGURE 32

RIGHT SIDE VIEW

STEP 33: (SEE FIGURE 33)

• Make sure the attachment clutch lever on the dash

panel is in the disengaged (down) position.

• Pivot the upper idler arm so that it rests against the

stop bolt and is pointing toward the front as shown.
Screw the trunnion (DD) along the threads of the
engagement rod until it is aligned at the front end of
the idler arm slot. Attach the trunnion to the slot using
the 3/8" thin washer (S) and a 5/64" hairpin cotter
(EE).

• Remove the engine pulley keeper from the side of the

tractor frame by removing the washer and nut that
secure the keeper. Attach the new pulley keeper (7)
supplied with the snow thrower, reusing the original
bolt, washer and nut.

NOTE:

Some tractors may already be equipped with a

pulley keeper that is identical to the new one supplied.

IDLER ARM

5/64" HAIRPIN
COTTER (EE)

STOP BOLT

3/8" THIN
WASHER (S)

NEW ENGINE PULLEY KEEPER (4)
WITH ORIGINAL BOLT, NUT, AND WASHER

TRUNNION (DD)

STEP 34: (SEE FIGURE 34)

• Assemble the short "V" belt onto the engine pulley

and then onto the large pulley on top of the clutch/idler
assembly. The belt must be placed to the inside of the
engine pulley keeper, the idler pulley and the keeper
bolt located beside the large pulley.

IMPORTANT:

Do Not

assemble the "V" belt around the

outside of the engine pulley keeper or the keeper bolt.

•

Go to step 48 on page 21.

FIGURE 34

VIEWED FROM UNDERNEATH

CLUTCH/IDLER ASSEMBLY

STEP 32: (SEE FIGURE 32)

• Be sure to lift up the front end of the engagement rod

(5) as shown when performing the next operation. You
can temporarily support the rod using a rubber band
tied to the engine pulley keeper.

• Attach the clutch/idler assembly to the tractor frame

as follows. Hook the assembly's notched rear pulley
frame brackets onto the two shoulder bolts you
assembled to the inside of the tractor frame. Lift the
front of the assembly and attach it to the R.H. and L.H.
hanger brackets using two pivot lock pins (HH) and
1/8" hairpin cotters (FF).

PIVOT LOCK PIN (HH)
(use second hole)

1/8" HAIRPIN COTTER (FF)

ENGAGEMENT

ROD (5)

ENGINE
PULLEY

KEEPER BOLT

IDLER
PULLEY

ENGINE
PULLEY
KEEPER

Left Side
of Tractor

«
...
14
15
16
17
18
...
»

Содержание LST42H





































Отзывы:

Нет отзывов

Похожие инструкции для LST42H

Бренд: Jacobsen Страницы: 14

Бренд: Ozito Страницы: 22

Бренд: FPZ Страницы: 100

RIBILAND PRBAT20

Бренд: Ribimex Страницы: 38

Бренд: Black+Decker Страницы: 84

Бренд: Poulan Pro Страницы: 22

4SISON BLAX2-M-EU

Бренд: Sabre Страницы: 48

Бренд: Troy-Bilt Страницы: 28

Бренд: Troy-Bilt Страницы: 29

Бренд: Cub Cadet Страницы: 32

Бренд: Gude Страницы: 40

IMPACT UTV Straight Blade Snowplow

Бренд: Western Страницы: 20

Бренд: FMI Страницы: 8

Бренд: RedMax Страницы: 32

Бренд: CERTIFIED Страницы: 10

Бренд: Tennant Страницы: 100

Бренд: Kraftixx Страницы: 167

Бренд: Milwaukee Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды