SpeedEPart LST42H Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 36

background image

21

STEP 48: (SEE FIGURE 47)

• Place the lift handle (2) into the lift bracket on the right

side of the snow thrower. Fasten the handle to the
bracket using two 5/16" x 1-3/4" hex bolts (B) and 5/16"
nylock nuts (Y).

FIGURE 48

RIGHT SIDE VIEW

NOTE:

Be sure the lift release cable's plastic covering

stays inserted into the trigger assembly for the next step.

STEP 49: (SEE FIGURE 48)

• Push the lift handle down into the locked position.

Insert the end of the cable wire into the hole in the
lift rod. Place the threaded fitting into the slot in the
lift bracket, with one hex nut above and one hex nut
and the lock washer below the slot. Tighten the nuts,
adjusting them to eliminate slack in the cable wire.
Refer also to the Service and Adjustments section on
page 27 in this manual.

HINT:

For easier assembly of the lift release cable, tilt the

snow thrower forward onto the spiral auger.

FIGURE 47

RIGHT SIDE VIEW

5/16" NYLOCK NUT

5/16" x 1-3/4"
HEX BOLT (B)

LIFT HANDLE (2)

ASSEMBLY OF THE SNOW THROWER

STEP 50: (SEE FIGURE 49)

• Tilt the snow thrower back down to the ground.
• Remove the nylon tie which fastens the auger

drive belt to the discharge housing, leaving the belt
assembled around the pulleys.

• Remove the nylon tie which fastens the chute crank

rod to the crank rod support tube.

• Assemble the crank rod support tube (3) to the

bracket on the left side of the discharge housing using
two 5/16" x 1-1/4" carriage bolts (J), and 5/16" nylock
nuts (Y).

5/16" NYLOCK NUT (Y)

5/16" x 1-1/4"
CARRIAGE BOLT (J)

CRANK ROD
SUPPORT TUBE (3)

DISCHARGE
HOUSING

FIGURE 49

LEFT SIDE VIEW

LIFT RELEASE
CABLE

HEX NUT

LOCK
WASHER

HEX NUT

CABLE
WIRE

LIFT
ROD

TRIGGER
ASSEMBLY

FIGURE 50

STEP 51: (SEE FIGURE 50)

• Install the plug (NN) into the end of the crank support

tube.

• Attach the chute tilt control assembly (8) to the top

side of the crank rod support tube using two 5/16" x
1-3/4" carriage bolts (I), bowed washers (U) and 5/16"
nylock nuts (Y).

CHUTE TILT CONTROL
ASSEMBLY (8)

5/16" x 1-3/4" CARRIAGE BOLT (I)

BOWED WASHER (U)

5/16" NYLOCK NUT (Y)

PLUG (NN)

«
...
19
20
21
22
23
...
»

Содержание LST42H





































Отзывы:

Нет отзывов

Похожие инструкции для LST42H

Бренд: Makita Страницы: 84

Бренд: Makita Страницы: 35

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 148

Бренд: Makita Страницы: 66

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 9

Бренд: BorMann Страницы: 9

BBL 870/40V PLUS

Бренд: F.F. Group Страницы: 32

Бренд: Stanley Страницы: 20

GAA_ _ P Series

Бренд: Gardner Denver Страницы: 46

Бренд: Honda Страницы: 75

Бренд: Toro Страницы: 28

SIMCO ION Aerostat Guardian

Бренд: ITW Страницы: 39

Бренд: Worx Страницы: 12

Бренд: Worx Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды