SpeedEPart LST42H Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

background image

10

FIGURE 12

VIEWED FROM LEFT SIDE

STEP 13: (SEE FIGURE 13)

• Assemble the drive belt onto the engine pulley first

and then onto the large pulley on top of the clutch/idler
assembly. The belt must be placed inside the engine
pulley belt keeper(s) and between the large pulley and
the keeper bolt next to it.

IMPORTANT:

Do Not

assemble the "V" belt outside of

the engine pulley keepers or outside of the keeper bolt
next to the large pulley.

•

Go to step 48 on page 21.

FIGURE 13

VIEWED FROM UNDERNEATH

CLUTCH/IDLER ASSEMBLY

FIGURE 11

ATTACH CLUTCH IDLER ASSEMBLY TO TRACTOR

STEP 12: (SEE FIGURE 12)

• Hook the rear of the clutch/idler assembly onto the

two shoulder bolts assembled to the tractor frame. Lift
the front of the assembly and attach it to the R.H. and
L.H. hanger brackets using two clevis pins (OO), six
washers (PP), and two 1/8" hairpin cotters (FF).

• Loosely attach the mower clutch cable to the left side

of the tractor frame with a nylon tie (LL).

Do not

pull

the nylon tie completely tight. The cable may need to
be removed from the nylon tie when using the mower
deck.

STEP 11: (SEE FIGURE 11)

• Find the cable clip that is attached to the left side

of the tractor frame underneath the footrest. Open
the clip and remove the mower clutch cable.

Do not

remove

the clip from the tractor frame. The cable

reattaches to the clip when using the mower deck.

• Move the attachment clutch lever on the dash panel to

the disengaged position.

• Place the clutch/idler assembly on the floor on the left

side of the tractor.

• Attach the tractor's mower clutch cable to the cable

bracket on the clutch/idler assembly. Secure the cable
housing guide (groove down) to the cable bracket
using the original collar and a 5/64" hair cotter pin (EE).

• Place the small spacer (II)on the welded pin on the

idler arm. Hook the end of the clutch cable spring
over the pin and secure it with a 1/4" washer (P)and a
5/64" hair cotter pin (EE).

• Align cable bracket with welded pin and tighten the

nut assembled in step 7.

L.H.
HANGER
BRACKET

1/8" HAIRPIN
COTTER (FF)

NYLON TIE (LL)

WASHERS (PP)

44044

SHOULDER
BOLT

MOWER
CLUTCH
CABLE

1/4" SPACER (II)

5/64" HAIR
COTTER PIN (EE)

CABLE
BRACKET

TRACTOR'S
CLUTCH CABLE

5/64" HAIR
COTTER PIN (EE)

1/4" WASHER (P)

ENGINE
PULLEY

ENGINE
PULLEY

Left Side
of Tractor

ENGINE
PULLEY
KEEPER

KEEPER BOLT

IDLER
PULLEY

«
...
8
9
10
11
12
...
»

Содержание LST42H





































Отзывы:

Нет отзывов

Похожие инструкции для LST42H

Powerlite 38273

Бренд: Toro Страницы: 20

Бренд: Stihl Страницы: 20

Бренд: Ryobi Страницы: 19

Hot Shot 950-9200

Бренд: TJERNLUND Страницы: 2

Бренд: AEG Страницы: 24

Бренд: AEG Страницы: 64

Бренд: AEG Страницы: 65

Бренд: Troy-Bilt Страницы: 28

Бренд: Troy-Bilt Страницы: 32

Storm Tracker 31AH7T74063

Бренд: Troy-Bilt Страницы: 28

Бренд: ebm-papst Страницы: 11

Бренд: ebm-papst Страницы: 11

Бренд: ebm-papst Страницы: 9

Бренд: ebm-papst Страницы: 10

Бренд: ebm-papst Страницы: 16

Бренд: Smithco Страницы: 66

Бренд: Faber Страницы: 20

Бренд: Milwaukee Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды