SpeedEPart LST42H Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 36

background image

12

STEP 19: (SEE FIGURE 18)

• Hook the rear of the clutch/idler assembly onto the

two shoulder bolts assembled to the outside of the
tractor frame. Lift the front of the assembly and attach
it to the R.H. and L.H. hanger brackets using two
clevis pins (OO), six washers (PP), and two 1/8"
hairpin cotters (FF).

FIGURE 18

VIEWED FROM LEFT SIDE

FIGURE 19

VIEWED FROM UNDERNEATH

FIGURE 17

STEP 18: (SEE FIGURE 17)

• Turn the clutch/idler assembly right side up.
• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

STOP

Did you choose the correct drive belt for
your tractor? Using the wrong length belt
may cause premature bearing or belt failure.

DRIVE BELT

FLAT IDLER
PULLEY

HEX BOLTS

1/8" HAIRPIN
COTTER (FF)

L.H. HANGER
BRACKET

PP

CLEVIS PIN (OO)

SHOULDER
BOLT

1/8"
HAIRPIN
COTTER (FF)

ENGINE
PULLEY

HEX BOLTS

FLAT IDLER
PULLEY

TENSIONING
CHAIN

LEFT SIDE
OF TRACTOR

STEP 20: (SEE FIGURE 19)

• Assemble the drive belt onto the engine pulley. You

may need to remove the belt from the large pulley on
the clutch/idler assembly in order to assemble it onto
the engine pulley. When re-assembling the belt onto
the large pulley, be sure the belt is between the large
pulley and the hex bolt next to it.

• Place tension on the belt by pulling the left side

tensioning chain out as far as the 3/32" hairpin cotter
(GG) that was installed in the chain in step 15 will
allow. Secure the chain in this position by inserting a
1/8" hairpin cotter (FF) through the chain.

•

Go to step 48 on page 21.

«
...
10
11
12
13
14
...
»

Содержание LST42H





































Отзывы:

Нет отзывов

Похожие инструкции для LST42H

KM 130/300 R D Classic

Бренд: Kärcher Страницы: 32

Бренд: Kärcher Страницы: 7

Бренд: Boss Snowplow Страницы: 28

Pro Attachment ES-210

Бренд: Echo Страницы: 32

Бренд: ebm-papst Страницы: 11

Бренд: VITO GARDEN Страницы: 40

Бренд: sunjoe Страницы: 12

Бренд: sunjoe Страницы: 16

Бренд: Worx Страницы: 22

Brushless Motor WG569E

Бренд: Worx Страницы: 104

Бренд: Toro Страницы: 60

Бренд: Texas Страницы: 25

Бренд: Texas Страницы: 45

Бренд: Texas Страницы: 63

Бренд: Texas Страницы: 64

Бренд: Tuchel Страницы: 48

Бренд: Tuchel Страницы: 65

Бренд: ATIKA Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды