background image

STEP 

5

Install RO Tap (continued)

IINSTALL REVERSE OSMOSIS TAP

Locate and organize your RO Tap install parts. See packing list on page 1 

Route the 3 tubes 

R

,

S

,

T

attached to the RO Tap Body 

through the RO Tap Base

Q

, but don’t connect the 

RO Tap Body

to the RO Tap Base

yet.  Then route the 3 tubes 

R

,

S

,

through the hole in the sink until 12” of 

tubing remains above the sink.  Lay RO Tap Body

on the counter top.

Mount Tap Body

to the sink hole by pushing the toggle bolts through the hole until the RO Tap Body

is flat against the sink 

surface. Position the toggle bolts to catch under the lower surface of the sink or counter, but ensure that they will not obstruct 
the tap stem from sitting in place.  Loosely tighten the toggle bolts until the RO Tap Base

is mounted loosely to the surface.

TIP:  Make sure to keep the “wings” of the toggle bolts free to allow all tubing and tap stem room 
TIP:  Install the tap base with the bolts at 5 and 11 o’clock positions to have the handle positioned at 90 degrees to the right

Hold the RO Tap Base

firmly and mount the RO Tap Body

to the RO Tap Base

by turning 1/4 clockwise to lock. Ensure 

the RO Tap Body Handle is positioned to your liking. 

TIP:  If there is not enough clearance for the tubing and the stem, the toggle wings may need to be adjusted to create more 

clearance.

Turn the RO Tap Body

1/4 turn counter-clockwise and remove the tap enough to tighten the RO Tap Base

toggle bolt 

screws firmly.  Do not over-tighten.  

1 0 

Mount the RO Tap Body

to the RO Tap Base

and turn 1/4  turn clockwise until it locks.

1 1 

Mount the RO Tap Spout 

to the RO Tap Body

P

by screwing spout nut to body.

5

O

P

S

R

T

Q  

Содержание PTL RO System




















Отзывы: