Spectrum Mopit 4 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 32

Spectrum Mopit 4 Скачать руководство пользователя страница 8

Page 8

Draining The Fresh Water Tank

Occasionally you may need
to drain the fresh water
tank. The tank will need to
be drained before shipping.
There is no harm in leaving
water in the fresh water
tank for an extended period
of time. You will want to
have the machine outside
or positioned over a floor
drain when you drain the
tank. To drain the tank pull off the tubing from the brass hose fitting,
and the water will immediately begin rushing out of the tank.

Cleaning The Water Filter

When you are not getting enough water onto the floor, clean the water
filter. Before you clean the fresh water filter make sure that the water
valve that is just above the filter, is turned off. Open the battery cover
by opening the bolt latch. Pull off the tubing connected to the solenoid.
Unscrew the base of the filter housing and remove the filter. Wash the
filter out in running water, and reassemble. Don’t forget to open the
manual water valve.

Scan this QR code with your smart phone to watch the Mopit
water filter video. You can view all of our Mopit movies on
the “Mopit Channel” at www.youtube.com.

MAINTENANCE / SERVICE

FOR PARTS AND SERVICE 1-800-290-2833

«
...
6
7
8
9
10
...
»

Содержание Mopit 4

































Отзывы:

Нет отзывов