background image

Important Safety and Care Instructions

Parts and Hardware Contents

• 

Read this owner’s manual before assembly or operation.

• 

Do not allow children to move the table.

• 

For indoor use only.  Do not install or store the table where it will be 

exposed to moisture.

• 

Do not block the ventilation openings.

• 

Do not allow anyone to sit, stand, or climb on the table.

• 

Use a damp, soft-cloth, or sponge, with mild soap or detergent solution 

to clean dirty surfaces.  Do not use harsh solvents or abrasives.

• 

This table is intended for institutional use.  It does not have any user-

serviceable parts or user-maintenance requirements.  If servicing is 

necessary, please contact Spectrum Industries for assistance.

General Electrical Safety:

• 

Keep power switches in the OFF position before plugging or 

unplugging from the wall outlet.

• 

Be sure total device / equipment load does not exceed 12-amps.

• 

Do not plug power cords into an extension cord.

• 

Inspect power cords for damage before each use.  Do not use cords 

that are damaged.

• 

Unplug power cord from electrical outlet by gripping the cord-do not 

unplug by pulling only on the cord.

• 

Do not step on, drive over, drag, or place objects on power cords.

• 

For added safety, plug into a grounded outlet controlled by a GFI 

(Ground Fault Interrupter) circuit breaker.

• 

Damaged electrical components can create signifi cant hazards to 

users and is not covered by the warranty.  Repairs should always be 

performed by a qualifi ed electrician.

• 

Electrical devices are not toys.  Children are often unaware of the 

hazards associated with electrical devices.  This table must always 

be used by adults or with adult supervision.

Warning

 - Relocating audio and/or video equipment to furniture not specifi cally 

designed to support audio and/or video equipment may result in death or 

serious injury due to the furnishing collapsing or over turning onto a child.

Warning

 - Death or serious injury may occur when children climb 

on audio and/or video equipment furniture.  A remote control or toys 

placed on the furnishing may encourage a child to climb on the 

furnishing and as a result the furnishing may tip over on to the child.

0115700R2 Page 2 of 17

(1) 0116173

table core with 

eLift legs

(2) 0115646

support plate

(12) 026064

1/4-20 x 5/8” 

PHMS

(2) 0115645

side 

worksurface

(8) 021551

1/4-20 x 2-3/4” 

PHMS

037779

5/16-18 glide

(4) fixed / set-and-go

(6) eLift

(4) 0113768

1” x 2” domed 

end cap

(1) 025069

glide wrench

(1) 0115574

table core with 

fixed legs

(1) 0115575

table core with 

set-and-go legs

(2) 0115641

fixed leg

(1) 0109397

control button

(1) 0109398

control button bracket

(2) 037542

#8 x 5/8” PHSM

(2) 0107023

Snap-in pine tree clip

(2) 059984

2” snap-in 

grommet

Содержание 37115


















Отзывы: