SpectraPure CR-RODI-90-10 Скачать руководство пользователя страница 2

Страница: 2 / 20

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

TABLE OF CONTENTS:

Thank You for your purchase of a SpectraPure

System. With proper

installation and maintenance, this system will provide you with high quality

water for years to come. All SpectraPure

products are rigorously tested by

us for safety and reliability. If you have any questions or concerns, please

contact our customer service department at 1.800.685.2783 or refer to our

online troubleshooting at www.spectrapure.com.

System Information

System Specifications

System Description

4-5

Working With Push Fittings

System Installation and Initialization

7- 8

Metering and Diagnostics

Using the Pressure Gauge

Using the Three-Probe TDS Meter

Membrane Output Calculation

10 -11

Membrane Rejection Test

System Maintenance

Sediment Prefilter Replacement

Carbon Block Prefilter Replacement

Deionization Cartridge Replacement

RO Membrane Replacement

14-15

System Storage and Troubleshooting

Membrane Troubleshooting Guide

Temperature Extremes

Tips For Long Membrane Life

Storage

Troubleshooting Guide for RO/DI Systems

Warranty Information

Replacement Parts and Accessories

ALL RIGHTS R ESERVED

No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise without the prior written permission of SpectraPure Inc.

Содержание CR-RODI-90-10





















Результаты поиска

Содержание CR-RODI-90-10

Отзывы:

Похожие инструкции для CR-RODI-90-10

Бренды по названию

Популярные бренды

SpectraPure CR-RODI-90-10, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CR-RODI-90-10

Отзывы:

Похожие инструкции для CR-RODI-90-10

Бренды по названию

Популярные бренды