Task Force Tips MASTER FOAM Скачать руководство пользователя

Страница: 1 / 12

INSTRUCTIONS FOR SAFE OPERATION AND MAINTENANCE

MASTER FOAM

FIXED

SELF-EDUCTING

FOAM NOZZLE

GPM

TASK FORCE TIPS

800.348.2686

www.tft.com

Fixed Flow

Rate:

Nominal

Pressure:

Nominal Foam

Percentages:

350, 500,

or 750 GPM

100 PSI

0.5%, 1%,

3%, or 6%

Read instruction manual before use. Operation of this device without

understanding the manual and receiving proper training is a misuse of this

equipment. A person who has not read and understood all operating and

safety instructions is not qualified to operate the MASTER FOAM self-

educting nozzle.
This instruction manual is intended to familiarize firefighters and

maintenance personnel with the operation, servicing, and safety

procedures associated with the MASTER FOAM self-educting nozzle.
This manual should be kept available to all operating and maintenance

personnel.

WARNING

Содержание MASTER FOAM













Результаты поиска

Содержание MASTER FOAM

Отзывы:

Похожие инструкции для MASTER FOAM

Бренды по названию

Популярные бренды

Task Force Tips MASTER FOAM, Инструкции по безопасной эксплуатации и техническому обслуживанию

Результаты поиска

Содержание MASTER FOAM

Отзывы:

Похожие инструкции для MASTER FOAM

Бренды по названию

Популярные бренды