background image

 

SPECTRACOM LIMITED WARRANTY 

 

LIMITED WARRANTY 

Spectracom warrants each new product manufactured and sold by 
it to be free from defects in software, material, workmanship, and 
construction, except for batteries, fuses, or other material normally 
consumed in operation that may be contained therein AND AS 
NOTED BELOW, for five years after shipment to the original 
purchaser (which period is referred to as the “warranty period”). 
This warranty shall not apply if the product is used contrary to the 
instructions in its manual or is otherwise subjected to misuse, 
abnormal operations, accident, lightning or transient surge, repairs 
or modifications not performed by Spectracom. 

The GPS receiver is warranted for one year from date of shipment 
and subject to the exceptions listed above. The power adaptor, if 
supplied, is warranted for one year from date of shipment and 
subject to the exceptions listed above. 

THE ANALOG CLOCKS ARE WARRANTED FOR ONE YEAR 
FROM DATE OF SHIPMENT AND SUBJECT TO THE EXCEPTIONS 
LISTED ABOVE. 

THE TIMECODE READER/GENERATORS ARE WARRANTED FOR 
ONE YEAR FROM DATE OF SHIPMENT AND SUBJECT TO THE 
EXCEPTIONS LISTED ABOVE. 

The Rubidium oscillator, if supplied, is warranted for two years from 
date of shipment and subject to the exceptions listed above. 

All other items and pieces of equipment not specified above, 
including the antenna unit, antenna surge suppressor and antenna 
pre-amplifier are warranted for 5 years, subject to the exceptions 
listed above.

 

WARRANTY CLAIMS  

Spectracom’s obligation under this warranty is limited to in-factory 
service and repair, at Spectracom’s option, of the product or the 
component thereof, which is found to be defective. If in 
Spectracom’s judgment the defective condition in a Spectracom 
product is for a cause listed above for which Spectracom is not 
responsible, Spectracom will make the repairs or replacement of 
components and charge its then current price, which buyer agrees 
to pay. 

Spectracom shall not have any warranty obligations if the 
procedure for warranty claims is not followed. Users must notify 
Spectracom of the claim with full information as to the claimed 
defect. Spectracom products shall not be returned unless a return 
authorization number is issued by Spectracom.  

 

Spectracom products must be returned with the description of the 
claimed defect and identification of the individual to be contacted 
if additional information is needed. Spectracom products must be 
returned properly packed with transportation charges prepaid. 

Shipping expense:

 Expenses incurred for shipping Spectracom 

products to and from Spectracom (including international customs 
fees) shall be paid for by the customer, with the following 
exception. For customers located within the United States, any 
product repaired by Spectracom under a “warranty repair” will be 
shipped back to the customer at Spectracom’s expense unless 
special/faster delivery is requested by customer.

 

Spectracom highly recommends that prior to returning equipment for 
service work, our technical support department be contacted to 
provide trouble shooting assistance while the equipment is still 
installed. If equipment is returned without first contacting the support 
department and “no problems are found” during the repair work, 
an evaluation fee may be charged. 

EXCEPT FOR THE LIMITED WARRANTY STATED ABOVE, 
SPECTRACOM DISCLAIMS ALL WARRANTIES OF ANY KIND 
WITH REGARD TO SPECTRACOM PRODUCTS OR OTHER 
MATERIALS PROVIDED BY SPECTRACOM, INCLUDING 
WITHOUT LIMITATION ANY IMPLIED WARRANTY OR 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

Spectracom shall have no liability or responsibility to the original 
customer or any other party with respect to any liability, loss, or 
damage caused directly or indirectly by any Spectracom product, 
material, or software sold or provided by Spectracom, replacement 
parts or units, or services provided, including but not limited to any 
interruption of service, excess charges resulting from malfunctions of 
hardware or software, loss of business or anticipatory profits 
resulting from the use or operation of the Spectracom product or 
software, whatsoever or howsoever caused. In no event shall 
Spectracom be liable for any direct, indirect, special or 
consequential damages whether the claims are grounded in 
contract, tort (including negligence), or strict liability.

 

EXTENDED WARRANTY COVERAGE

  

Extended warranties can be purchased for additional periods 
beyond the standard five-year warranty. Contact Spectracom no 
later than the last year of the standard five-year warranty for 
extended coverage.

 

SPECTRACOM    95 Methodist Hill Drive    Rochester, NY 14623 

+1.585.321.5800  FAX: +1.585.321.5218  www.spectracomcorp.com  [email protected]

 

Содержание 9289







































































































































































































Отзывы: