background image

8999071EN: v1.410/10/2019 

19  

Original instructions (ENGLISH) 

Website:  www.spearheadmachinery.com 

 

 

Finishing Work 

 
After the job done disconnect the PTO shaft, lift the machine and transport it onto the appropriate place. 
 

IMPORTANT:

 During transport reduce the speed, especially on bumpy roads. The weight of the machine may 

render driving difficult and damage the machine itself. During transport the machine must be always in the 
transport position. 
 

IMPORTANT:

 PTO shaft must be disconnected during transport. 

 

DANGER!

   At disconnecting the machine respect the warning rules for connecting the machine. 

 
 
 

IMPORTANT:

 Before disconnection of the machine put on a pin-blockade of the linkage (Figure 26 (2)). 

 
 

7.1 

Storage 

 
Put the machine on the flat not soft ground. Put the support feet into the appropriate position. (Figure 27).To 
avoid a corrosion store the machine on a dry place. 
 
In the case of small place put together the arm of the mower and push the machine to the tractor that arm comes 
close to the body of the machine. Put the support feet into the standing position and lift down the machine. 
Disconnect the PTO shaft and put it on the hook (Figure 26 (1)). Disconnect the machine from the tractor 3-point 
hitch. Put a blockade for linkage on (Figure 26 (2)). 
 

 

 

Figure 26 

Figure 27 

 

WARNING!

   At disconnecting the machine from the tractor block the rear roller with a piece of wood for 

stability of the machine. 

 
 

7.2 

Cleaning 

 
To avoid any corrosion clean the machine after each working day, especially working tools, bearings etc. Be 
careful to avoid damaging hydraulic pipes, bearings and colour. 
 

 

Figure 28 

Содержание 8999071

































Отзывы: