6
EN
FK 3014
▪ Never use the machine with a damaged ca
-
ble. Do not touch the damaged cable and pull
the mains plug when the cable is damaged
while operating. Damaged cables increase
the risk of electric shock.
▪ Use clamps or a vice to secure your work
whenever possible.
▪ Do not leave any tools in the work area.
▪ Use only diamond cutting wheels.
▪ Never use damaged or unbalanced wheels.
▪ Protect the diamond wheels from shock.
▪ Do not switch on the machine fed into the
material and leave the machine only when
the wheels have halted rotation.
▪ Do not overload the power tool.
▪ This power toll is delivered with a wheel
guard, never operate it without a wheel
guard.
▪ Protect your hands from the rotating cutting
wheels.
▪ Feed the wall chaser into the material only if
the machine is switched on.
▪ Never apply pressure to stop the wheel rota
-
tion after switching off the wall chaser.
▪ Always switch off the machine prior to leav
-
ing it down.
▪ Do not leave the switched off machine on
roller supports 10, always place it leaning on
its side.
▪ Carry the tool only by the auxiliary handle 8
and the body of the driving machine.
▪ Use genuine spare parts and accessories
only.
▪ The tool must be used only for its prescribed
purpose. Any use other than those men-
tioned in this Manual will be considered a
case of misuse. The user and not the manu-
facturer shall be liable for any damage or
injury resulting from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and serv-
ice the machine have to be acquainted with
this Manual and must be informed about its
potential hazards. Children and frail peo-
ple must not use this tool. Children should
be supervised at all times if they are in the
area in which the tool is being used. It is also
imperative that you observe the accident
prevention regulations in force in your area.
The same applies for general rules of occu-
pational health and safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any dam-
age resulting from such changes.
▪ The power tools must not be used outdoors
in rainy weather, or in moist environment (af
-
ter rain) or in close vicinity with easily flam
-
mable liquids and gases. The working place
should be well lit.
V - Know your product
Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Wheel guard
2. Arm
3. Cutting depth scale
4. Screw for fixing the groove depth
5. Driving machine
6. End stop for fixing the operating
position of the driving machine
7. Screw for fixing the driving machine
8. Auxiliary handle
9. ON/OFF switch
10. Roller support
11. Flange
12. Diamond wheel
13. Spacer washer
14. Lock nut
15. Spindle lock button
16. Dust extraction pipe
VI - Operation
This power tool is supplied from single-phase
alternating current mains only. It is double insu-
lated according to EN 60745-1 and IEC 60745
and can be connected to grounded or not
grounded sockets. This power tool is radio
suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for cutting grooves
with adjustable width and depth only in the
materials, specified on the wheels used with
this tool (concrete, aerated concrete, masonry,
stone, etc., for laying electric installation, duct
and gas armature, cable networks, etc. The
machine is designed for dry cutting only.
PRIOR TO INITIAL OPERATION
▪ The machine may be delivered with the
wheel guard mounted at the factory. Ensure
that the wheel guard is mounted properly
and fixed reliably prior to the initial and any
following operation.
▪ The machine may be delivered with the
wheel mounted at the factory. Ensure that
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
