sparkfun KIT-14556 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 63

background image

Introducing the Red Green Blue (RGB) LED

The Red Green Blue (RGB) LED is 3 LEDs in one. The RGB has four pins
with each of the three shorter pins controlling an individual color: red, green
or blue. The longer pin of the RGB is the common ground pin. You can
create a custom colored LED by turning different colors on and off to
combine them. For example, if you turn on the red pin and green pin, the
RGB will light up as yellow.

But which pin is which color? Pick up the RGB so that the longest pin
(common ground) is aligned to the left as shown in the graphic below. The
pins are Red, Ground, Green and Blue – starting from the far left.

Note:

When wiring the RGB, each colored pin still needs a current-

limiting resistor in line with the RedBoard pin that you plan to use to
control it, as with any standard LED.

Hardware Hookup

Ready to start hooking everything up? Check out the wiring diagram and
hookup table below to see how everything is connected.

Polarized

Components

Pay special attention to the component’s markings
indicating how to place it on the breadboard. Polarized
components can only be connected to a circuit in one
direction. Polarized components are highlighted with a
yellow warning triangle in the table below.



Page 16 of 63

«
...
14
15
16
17
18
...
»

Содержание KIT-14556
































































Отзывы:

Нет отзывов

Похожие инструкции для KIT-14556

Бренд: GE Страницы: 425

Бренд: Parker Страницы: 44

Бренд: Datapath Страницы: 12

Бренд: Vega Страницы: 20

Бренд: Newport Страницы: 417

Бренд: ZPA Pecky, a.s. Страницы: 36

Бренд: Tech 21 Страницы: 2

Бренд: mikroElektronika Страницы: 3

Бренд: Window Master Страницы: 7

Бренд: Teledyne Страницы: 102

Бренд: TSM Страницы: 2

Бренд: MQ Multiquip Страницы: 74

STM32F469 Series

Бренд: ST Страницы: 31

Бренд: Unika Страницы: 14

Бренд: IEI Technology Страницы: 81

SN32F260 Series

Бренд: SONIX Страницы: 141

Бренд: Barco Страницы: 2

Бренд: Fright Ideas Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды