manualshive.com logo in svg

Spaceman 6210-C Series, Руководство по эксплуатации машины

Поделиться
Скачать
Spaceman 6210-C Series Скачать руководство пользователя страница 17

 

15

 

Operating Control : 

Wash/Standby/Defrost

 

Standby Mode

 

IMPORTANT: When the machine will NOT be utilized for several hours, place it in STANDBY mode to 

conserve electricity and reduce product loss. 

 

In STANDBY, product remains below 4

o

C (40

o

F) in both the cylinders and hoppers, but will NOT be frozen.

 

To turn on STANDBY mode:

 

• 

Press RESET buttons, then STANDBY buttons

 

• 

Displays read STANDBY when machine is in STANDBY mode

 

 

To turn off STANDBY mode:

 

• 

Press RESET buttons

 

• 

Machine is ready for a new mode selection

 

Wash Mode

 

To turn on Wash mode:

 

• 

Press RESET button, then WASH button

 

• 

Displays read WASHING when machine is in Wash mode

 

 

To turn off Wash mode:

 

• 

Press RESET button

 

• 

Machine is ready for a new mode selection

 

To turn on DEFROST mode:

 

• 

Press RESET button, then STANDBY for 3 seconds

 

• 

Displays read DEFROST when machine is in DEFROST mode

 

 

To turn off DEFROST mode:

 

• 

Press RESET button

 

• 

Machine is ready for a new mode selection

 

Defrost Mode

 

IMPORTANT: 

Heat up frozen product in cylinder for faster draining and cleaning.

 

Use right before draining; start draining after it completes in 3 to 5 minutes. 

 

Nightly standby procedure

 

Store closing:

 

1.

 

With machine in FREEZE mode, remove air tubes.

 

2.

 

Clean air tubes, hopper agitators, design cap, front 

trip tray, and internal trip tray.

 

3.

 

Insert into machine upside down (inlet hole on the 

side of the air tube at the top).

 

4.

 

Confirm product is above minimum product level 

(top of hopper agitator blade) in hoppers.

 

5.

 

Press RESET, press STANDBY.

 

 

Store opening:

 

1.

 

Open draw handles to draw 170 g to 227 g (6 oz. to 8 

oz.) of product; discard product.

 

2.

 

Press RESET, press FREEZE. Wait until machine finish-

es freeze cycle and motors stop turning.

 

3.

 

Insert air tubes into machine with correct orientation 

(inlet hole on the side of the air tube at the bottom).

 

4.

 

Machine is ready for normal operation.

 

Store closing:

 

1.

 

Clean hopper covers, hopper agitators, design 

cap, front trip tray, and internal trip tray.

 

2.

 

Confirm product is above minimum product 

level (top of hopper agitator blade) in hoppers.

 

3.

 

Press RESET, press STANDBY.

 

 

Store opening:

 

1.

 

Open draw handles to draw 170 g to 227 g (6 

oz. to 8 oz.) of product; discard product.

 

2.

 

Press RESET, press FREEZE. Wait until machine 

finishes freeze cycle and motors stop turning.

 

3.

 

Machine is ready for normal operation.

 

Gravity Feed

 

Pump Feed

 

Содержание 6210-C Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды