Spacelabs 91518 Скачать руководство пользователя страница 6

Страница: 6 / 92

Introduction

91518 Multigas Analyzer Service Manual

1-2

Compatibility

The 91518 Multigas Analyzer is designed for use with Ultraview SL, Ultraview, and UCW

monitors.

Ultraview SL

™

• Ultraview SL2400 (91369), SL2600 (91370), SL2700 (91387-27), SL2800 (91387-28)

Ultraview

• UCW (90385)*, Ultraview 1700 (90387)*, Ultraview 1500 (90363), Ultraview 1600 (90364), Ultraview 1050

(90369), Ultraview 1030 (90367)

* Some UCW (S/N below 385-3xxxxx) and Ultraview monitors (S/N below 387-1xxxxx) do not support all

waveforms and display options, such as colors.

Dimensions

Height

17.15 cm (6.75 inches) (enclosure: 14.605 cm [5.75 inches]); feet: 1.27 cm
(0.5 inches)

Width

15.24 cm (6 inches)

Depth

28.45 cm (11.2 inches) (enclosure: 21.59 cm [8.5 inches]); gas module protrudes
from front 4.572 cm (1.8 inches); handle in back of enclosure protrudes 2.286 cm
(0.9 inches)

Weight

3.714 kg (8.19 lbs)

Содержание 91518





























































































Результаты поиска

Содержание 91518

Отзывы:

Бренды по названию

Популярные бренды

Spacelabs 91518, Руководство по обслуживанию

Результаты поиска

Содержание 91518

Отзывы:

Бренды по названию

Популярные бренды