Sovereign SCS 38 Скачать руководство пользователя страница 16

Страница: 16 / 20

TROUBLESHOOTING THE ENGINE

Problem

Probable Cause

Corrective Action

Unit wonʼt start or starts but will
not run.

Incorrect starting procedures.

Follow instructions in the User
Manual.

Incorrect carburetor mixture
adjustment setting.

Have carburetor adjusted by an
Authorized Service Center.

Fouled spark plug

Clean / gap or replace plug.

Fuel filter plugged.

Replace fuel filter.

Unit starts, but engine has low
power.

Incorrect lever position on choke.

Move to RUN position.

Dirty spark arrester screen

Replace spark arrester screnn

Dirty air filter.

Remove, clean and reinstall filter.

Incorrect carburetor mixture
adjustment setting.

Have carburetor adjusted by an
Authorized Service Center.

The distance between the motor
and the ignition coil has changed

Arrange for an authorized
Customer Service workshop to
adjust the distance between the
rotor and the ignition coil to
0.3-0.4 mm

Engine hesitates.
No power under load.

Incorrect carburetor mixture
adjustment setting.

Have carburetor adjusted by an
Authorized Service Center.

Runs erratically.

Incorrectly gapped spark plug.

Clean / gap or replace plug.

Smokes excessively.

Incorrect carburetor mixture
adjustment setting.

Have carburetor adjusted by an
Authorized Service Center.

Incorrect fuel mixture.

Use properly mixed fuel (40:1
mixture).

Chain does not move

chain brake activated

release chain brake

Poor cutting performance

blunt chain

sharpen chain

chain incorrectly fitted

check chain fitment

chain tension

check tension

Saw works only with difficulty,
chain jumps off term

chain tension

check tension

Chain becomes hot

chain lubrication

check oil level
check chain lubricatiom

Anleitung SCS 38_SPK7:_ 20.11.2006 15:43 Uhr Seite 16

Содержание SCS 38





















Результаты поиска

Содержание SCS 38

Отзывы:

Бренды по названию

Популярные бренды

Sovereign SCS 38, Руководство по эксплуатации

Результаты поиска

Содержание SCS 38

Отзывы:

Бренды по названию

Популярные бренды