Sovereign SCS 38 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 20

Sovereign SCS 38 Скачать руководство пользователя страница 15

CHAIN TENSION:

Check the chain tension frequently and adjust as
often as necessary to keep the chain snug on the
bar, but loose enough to be pulled around by hand.

BREAKING IN A NEW SAW CHAIN:

A new chain and bar will need chain readjustment
after as few as 5 cuts. This is normal during the
break-in period, and the interval between future
adjustments will begin to
lengthen quickly.



WARNING:

Never have more than 3 links

removed from a loop of chain. This could cause
damage to the sprocket.

CHAIN LUBRICATION:

Always make sure the automatic oiler system is
working properly. Keep the oil tank filled with Chain,
Bar and Sprocket Oil.
Adequate lubrication of the bar and chain during
cutting operations is essential to minimize friction
with the guide bar.
Never starve the bar and chain of lubricating oil.
Running the saw dry or with too little oil will decrease
cutting efficiency, shorten saw chain life, cause rapid
dulling of chain, and lead to excessive wear of bar
from overheating. Too little oil is evidenced by smoke
or bar discoloration.

ORDERING REPLACEMENT PARTS

Please quote the following data when ordering
replacement parts:

Type of machine

Article number of the machine

Identification number of the machine

Replacement part number of the part required

Helpline Numbers:
UK:

0151 649 1500

IRE:

189 094 6244

GB

15

Anleitung SCS 38_SPK7:_ 20.11.2006 15:43 Uhr Seite 15

«
...
13
14
15
16
17
...
»

Содержание SCS 38





















Отзывы:

Нет отзывов