background image

SOUTHWORTH

ZLS SERIES — FLOOR HEIGHT LIFT TABLES    

21

Southworth Products Corp warrants this product to be free from defects 
in material or workmanship for a period of 

two (2) years

 of  single 

shift usage from date of  shipment, providing claim is made in writing 

within that time period. This warranty shall not cover modified designs 

for special applications, failure or defective operation caused by misuse, 

misapplication, negligence or accident, exceeding recommended capacities, 

failure to perform required maintenance or altering or repairing, unless 

alteration is authorized by Southworth Products Corp. Except as set forth 

herein, there are no other warranties, express or implied, including the 

warranties of  merchantability and fitness for a particular purpose, all of  

which are hereby excluded.

Southworth Products Corp makes no warranty or representation with re-

spect to the compliance of  any product with state or local safety or prod-

uct standard codes, and any failure to comply with such codes shall not 

be considered a defect of  material or workmanship under this warranty. 

Southworth Products Corp shall not be liable for any direct or consequen-

tial damages arising out of  such noncompliance.

Southworth Products Corp’s obligation under this warranty is limited to 

the replacement or repair of  defective components at its factory or another 

location at Southworth Products Corp’s discretion. This is buyer’s sole rem-

edy. Except as stated herein, Southworth Products Corp will not be liable 

for any loss, injury or damage to persons or property, nor for direct, indi-

rect, or consequential damage of  any kind, resulting from failure or defec-

tive operation of  said product.

This warranty may be altered only in writing by Southworth Products Corp, 

Portland, Maine.

SOUTHWORTH PRODUCTS CORP
P.O. Box 1380, Portland, ME  04104-1380
Telephone: 800-743-1000 / 207-878-0700
Fax: 207-797-4734
www.SouthworthProducts.com

2 YEAR WARRANTY

Содержание ZLS Series























Отзывы: