Sound Skulptor MP573 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 12

background image

www.soundskulptor.com

Document revision 2.3 – Last modification : 27/05/21

MP573 Assembly guide – Main PCB, A side

19. DI Connector

Solder the connector socket CN3a. Solder one pin first, check verticality, then solder the other pins.

20. Output TX connector

Solder the connector socket CN2. Solder one pin first, check verticality, then solder the other pins.

21. Link Connector

Solder the connector header CN. Solder one pin first, check verticality, then solder the other pins.

22. Trimmer potentiometer

Add P2. Solder one pin, check verticality then solder the other pins.

Copyright ©2015 SoundSkulptor

«
...
3
4
5
6
7
...
»

Содержание MP573













Отзывы:

Нет отзывов

Похожие инструкции для MP573

Бренд: Ecler Страницы: 20

Бренд: Ecleree Страницы: 28

Бренд: Ecleree Страницы: 42

Bassman Bassman 100

Бренд: Fender Страницы: 20

Бренд: Fender Страницы: 156

G-DEC 3 Thirty & Fifteen

Бренд: Fender Страницы: 24

Бренд: LA Audio Страницы: 7

Бренд: Xaoc Devices Страницы: 6

Бренд: Gato Audio Страницы: 16

Бренд: Kramer Страницы: 4

Бренд: AMERITRON Страницы: 19

Бренд: Supertech instruments Страницы: 6

Two-Rock Custom Reverb Signature V3

Бренд: K&M Analog Designs Страницы: 9

The Beast 30W Plus - head

Бренд: Laboga Страницы: 16

Бренд: RDP Group Страницы: 12

Бренд: Revox Страницы: 9

Бренд: SUPRO Страницы: 8

Бренд: Primare Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды