Sound Skulptor MP573 Скачать руководство пользователя страница 4

Страница: 4 / 12

www.soundskulptor.com

Document revision 2.3 – Last modification : 27/05/21

MP573 Assembly guide – Main PCB, A side

12. Jumper header

Solder jumper header JMP3. Solder one pin first, check verticality, then solder the other pins.
JMP1 and JMP2 are for future use. They allow moving the insert point, situated between first and second

stage, to the back connector. When used you will also need to add 2 wires shown in the bottom side
layout (mp573-layout.pdf).

13. Ceramic capacitors

Add C2, C3, C4, C5, C16, C17, C25, C28, C30, C31, C32, C33.

14. Vertical resistors

Insert R3, R7 to R16, R19, R20, R22, R23, R25, R38.
These resistors are placed vertically. Bend one leg 180° sharp
and insert.

15. Film capacitors

Add C9, C15, C21, C26.

16. Tantalum capacitors

Add C14, C24, C20, C22. The plus lead is the longest lead.

Warning

: The +lead must go into the +hole. Do not reverse !

17. Transistors

Add Q1 to Q5.

Warning

: Watch out the transistor direction.

18. PTC 1

Solder the thermistor PTC1.

Содержание MP573













Результаты поиска

Содержание MP573

Отзывы:

Похожие инструкции для MP573

Бренды по названию

Популярные бренды

Sound Skulptor MP573, Инструкция по сборке

Результаты поиска

Содержание MP573

Отзывы:

Похожие инструкции для MP573

Бренды по названию

Популярные бренды