Sony UWP-V1, Руководство по обслуживанию

Страница: 69 / 164

2-49
UWP Series
(2) S/N Check
1. Set the URX-P2 as follows :
Channel setting :
U30 model ;Group 03, 3201 channel (578.125 MHz)
U42 model ;Group 03, 4401 channel (650.125 MHz)
CE62 model ;Group 04, 6332 channel (810.000 MHz)
CE67 model ;Group 04, 6832 channel (850.000 MHz)
KR model
;Group 12, 6001 channel (746.125 MHz)
RF Squelch : OFF (For setting, refer to “Setting the
Squelch OFF mode” on page 2-42)
2. Connect the audio analyzer to the OUTPUT connector
via MIC amp.
3. Connect the signal generator to the CN201/RF-130
board with the MM-SMA conversion connector and
the RF adjusting cable.
4. Set the signal generator as follows :
Signal generator setting
FREQUENCY (carrier frequency) :
U30 model ; 578.125 MHz
U42 model ; 650.125 MHz
CE62 model ; 810.000 MHz
CE67 model ; 850.000 MHz
KR model ; 746.125 MHz
RF OUTPUT (Output level) : 60 dB u V
EMF
(= _ 53 dBm)
MODULATION (Modulation frequency) : 1 kHz
DEVIATION (Frequency deviation)
:
±
5 kHz
5. Read the output level of the OUTPUT connector (Audio
analyzer indication level).
This level is specified to be 0 dB.
6. Turn OFF the MODULATION (modulation frequency)
of the signal generator (No modulation).
7. Check that output level of the OUTPUT is 62 dB or
more (S/N is
_
62 dB or less with A-weighted filter) as
compared with the level of procedure 5 above.
8. Change the RF OUTPUT (output level) of the signal
generator as shown below.
RF OUTPUT (output level) : 15 dB
u
V
EMF
(=
_
98 dBm)
9. Check that output level of the OUTPUT is 36 dB or
more (S/N is
_
36 dB or less with A-weighted filter) as
compared with the level of procedure 5 above.
10. Change the RF OUTPUT (output level) of the signal
generator as shown below.
RF OUTPUT (output level) : 60 dB
u
V
EMF
(=
_
53 dBm)
11. Set the audio analyzer to the distortion mode.
12. Check that distortion ratio is
_
40 dB or less (1 % or
less) with A-weighted.
13. Connect the signal generator to the CN101/RF-130
board with the MM-SMA conversion connector and the
RF adjusting cable.
14. Perform the procedures 4 to 12 above.
15. Set the channel and FREQUENCY (carrier frequency)
of the signal generator as shown
1
and
2
below.
Perform the procedures 3 to 14 above, for each channel
setting (
1
and
2
).
1
Channel setting :
U30 model ; Group 01, 6201 channel (566.125 MHz)
U42 model ; Group 01, 6601 channel (638.125 MHz)
CE62 model ; Group 01, 6201 channel (798.125 MHz)
CE67 model ; Group 01, 6701 channel (838.125 MHz)
KR model
; Group 00, 5901 channel (740.125 MHz)
Signal generator setting :
FREQUENCY (carrier frequency)
U6264 model
; 566.125 MHz
U6668 model ; 638.125 MHz
CE62 model ; 798.125 MHz
CE67 model ; 838.125 MHz
KR model ; 740.125 MHz
2
Channel setting :
U30 model ; Group 00, 3201 channel (589.875 MHz)
U42 model ; Group 00, 4401 channel (661.875 MHz)
CE62 model ; Group 00, 6463 channel (821.875 MHz)
CE67 model ; Group 00, 6964 channel (862.000 MHz)
KR model
; Group 00, 6047 channel (751.875 MHz)
Signal generator setting:
FREQUENCY (carrier frequency):
U30 model
; 589.875 MHz
U42 model ; 661.875 MHz
CE62 model ; 821.875 MHz
CE67 model ; 862.000 MHz
KR model ; 751.875 MHz