Sony SSC-DC193 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 50

background image

3-1

SSC-M183/M183CE/M188CE/M383/M383CE/M388CE

SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P

Section 3

Troubleshooting

3-1. Black and White Camera

Applicable models: SSC-M183/M183CE/M188CE/M383/M383CE/M388CE

1. Image is too bright.

OFF

CCD-IRIS

Image is too bright.

Type of the used lens?

.

When DC servo lens is used,
adjust with the LEVEL volume
on the rear panel.

.

When video servo lens is used,
adjust the lens level with
the LEVEL volume.

The LEVEL volume does not
operate.

Replace the rear (R) board.

Position of the

CCD-IRIS switch?

When the image is not improved
after the AGC switch on the rear
panel is set to AGC side, adjust
the lens aperture.

Close the lens aperture.

Readjust the LEVEL volume.

When the image is not improved
after the AGC switch on the rear
panel is set to AGC side,
readjust with the LEVEL volume.

Normal

Auto iris

«
...
25
26
27
28
29
...
»

Содержание SSC-DC193



















































Отзывы:

Нет отзывов

Похожие инструкции для SSC-DC193

Бренд: Olympia Страницы: 5

Бренд: Lampa Страницы: 2

Бренд: Caddx-Caddi Controls Страницы: 6

Бренд: Safety Vision Страницы: 21

EasyLook PPDF17000

Бренд: Abus Страницы: 23

Бренд: Abus Страницы: 4

Бренд: Dante Страницы: 7

Бренд: Yolink Страницы: 30

Бренд: Pyronix Страницы: 2

Бренд: dallmeier Страницы: 44

Бренд: Grundig Страницы: 98

Бренд: Teledyne Detcon Страницы: 15

Бренд: Surveon Страницы: 59

Бренд: Zavio Страницы: 16

Бренд: Amcrest Страницы: 17

Бренд: Streamax Страницы: 8

Бренд: DBI SALA Страницы: 28

XF10-24mmF4 R OIS

Бренд: FujiFilm Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды