Sony SSC-DC193 Скачать руководство пользователя страница 30

Страница: 30 / 50

3-4

SSC-M183/M183CE/M188CE/M383/M383CE/M388CE

SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P

3-2. Color Camera

Applicable models: SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P

1. Image is too dark or invisible.

Yes

Image is too dark or invisible.

Check the connection of
the BNC connector.

Is the Video

signal output from the

BNC connector?

Type of the used lens?

Open the lens aperture.

Is the image displayed?

To A

Is the Video

signal output from 1 pin

of CN204 on the signal

(PC) board?

Measure the voltage of each pin
of CN102 on the power (AC) board.
Measurement point: CN102/AC

board

Pin 1 = 15 V
Pin 2 = 9 V
Pin 3 = 5 V
Pin 4 = 3.3V
Pin 5 =

7 V

Is the output

voltage correct?

Is the

servo lens switch

on the rear panel set to the

used lens (DC or

VIDEO)?

Is the monitor

brightened when the lens

is removed?

Adjust the lens aperture

Reconnect the cable of
the servo lens.

Adjust correctly with the
LEVEL volume.

Replace the rear (R) board

Replace the signal (PC) board.

Replace the power (AC) board.

Set the switch correctly.

Reconnect the cable of
the servo lens and readjust
the following:
DC servo lens: LEVEL volume

on the rear panel

VIDEO servo lens: Lens LEVEL

Is the image

correctly displayed?

When the image is not improved
after adjusting with the LEVEL
volume, replace the rear board.

Manual lens

Servo lens

Содержание SSC-DC193



















































Результаты поиска

Содержание SSC-DC193

Отзывы:

Похожие инструкции для SSC-DC193

Бренды по названию

Популярные бренды

Sony SSC-DC193, Руководство по обслуживанию

Результаты поиска

Содержание SSC-DC193

Отзывы:

Похожие инструкции для SSC-DC193

Бренды по названию

Популярные бренды