Sony SSC-DC193 Скачать руководство пользователя страница 13

Страница: 13 / 50

1-7

SSC-M183/M183CE/M188CE/M383/M383CE/M388CE

SSC-DC193/DC193P/DC198P/DC393/DC393P/DC398P

AC-24 board

Harness

PB-2001
/PC-2001 board

Solder

CN102

1-4-2. PB-2001/PC-2001 Board

For SSC-M183/M183CE/M383/M383CE/DC193/
DC193P/DC393/DC393P

Removal

Remove the top cover. (Refer to Section 1-3-1.)

Remove the front cover assembly. (Refer to Section 1-

3-2.)

Remove the rear chassis assembly. (Refer to Section 1-

3-3.)

Remove the plate reinforcement. (Refer to Section 1-

6.)

Remove the PB-2001/PC-2001 board from the bottom

chassis. (Refer to Section 1-3-3.)

Remove the AC-24 board from the bottom chassis.

(Refer to Section 1-3-3.)

Remove the solder from the connector (CN102) on the

AC-24 board, then remove the PB-2001/PC-2001
board.

Marking

Bottom chassis

Groove

AC-24 board

Harness

PB-2001
/PC-2001 board

Solder

CN102

Claw

Installation

Attach the AC-24 board in the reverse order of steps 6

and 7 of the Removal.

Insert the marking section of the PB-2001/PC-2001

board into the groove of the bottom chassis, then
attach in the direction indicated by the arrow.

Attach the PB-2001/PC-2001 board so that it is placed
outside of the claw of the bottom chassis.

Attach the PB-2001/PC-2001 board in the reverse
order of steps 1 to 3.

Содержание SSC-DC193



















































Результаты поиска

Содержание SSC-DC193

Отзывы:

Похожие инструкции для SSC-DC193

Бренды по названию

Популярные бренды

Sony SSC-DC193, Руководство по обслуживанию

Результаты поиска

Содержание SSC-DC193

Отзывы:

Похожие инструкции для SSC-DC193

Бренды по названию

Популярные бренды