Sony SAITe1300-F Скачать руководство пользователя | Manualshive

Страница: 25 / 50

background image

25

Chapter 2 Installation

Installing the S-AIT Tape Drive Unit

The S-AIT Tape Drive Unit weights about 7 kg (15.4 lb.) and has the following
dimensions. Make sure that the surface where you will install the S-AIT Tape
Drive Unit is appropriate before installing the unit.

Note

Install the S-AIT Tape Drive Unit on a horizontal surface near an AC power
outlet. Make sure that you leave gap of about 150 mm (5.9 in.) behind the rear
of the unit to allow air to circulate.

Recommended positioning of the unit

• Always position the unit horizontally.
• Away from moving air, such as fans, open windows, or air conditioners.
• Away from devices such as facsimiles to avoid toner and paper dust.

The S-AIT Tape Drive Unit should not be stacked. Do not place anything on top
of the unit.

86 mm (3.4 in.)

372 mm (14.6 in.)

210 mm
(8.3 in.)

50 mm (2.0 in.)

210 mm (8.3 in.)

150 mm
(5.9 in.)

372 mm (14.6 in.)

50 mm (2.0 in.)

Rear

Front

«
...
23
24
25
26
27
...
»

Содержание SAITe1300-F



















































Отзывы:

Нет отзывов

Похожие инструкции для SAITe1300-F

Бренд: Qlogic Страницы: 20

Hawk 1 ST11200N

Бренд: Seagate Страницы: 84

Бренд: ramia Страницы: 3

TS-h1886XU-RP-R2

Бренд: QNAP Страницы: 62

Бренд: Arrow Storage Products Страницы: 44

Cold Frame Single

Бренд: Palram Страницы: 11

Бренд: Chieftec Страницы: 18

Exos ST2000NM0075

Бренд: Seagate Страницы: 42

Бренд: AIC Страницы: 79

Бренд: Iomega Страницы: 48

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 4

VAIO PCGA-HD740

Бренд: Sony Страницы: 7

Бренд: Sony Страницы: 16

VAIO VGP-UHDP04

Бренд: Sony Страницы: 23

Vaio VGP-UHDM10

Бренд: Sony Страницы: 27

VAIO VGP-UHDM08

Бренд: Sony Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды