Sony SAITe1300-F Скачать руководство пользователя | Manualshive

Страница: 27 / 50

background image

27

Chapter 2 Installation

Connecting the SCSI Bus Cable (SAITe1300-S only)

Connect the SAITe1300-S (SCSI model) and the host computer with a SCSI
cable. This section describes how to do so. Use an Ultra 160/m SCSI LVD cable
commonly sold in stores to connect the unit to the SCSI bus. The SAITe1300-S
uses a 68-pin half pitch connector.

Caution

• Do not connect the SAITe1300-S to a HVD (High Voltage Differential) SCSI

bus. If you do, the unit or other devices on the SCSI bus may be damaged.

• Turn off all the connected devices before connecting the SCSI cable,

including the SAITe1300-S and the host computer.

• If the SAITe1300-S is the last or only device on the SCSI bus, make sure that

you connect the supplied terminator to the open connector.

• Make sure that the SCSI connectors are securely connected.
• With LVD (Low Voltage Differential) SCSI, make the total length of the

SCSI cable (internal and external) connecting the host computer and the
device at the end of the SCSI bus shorter than 12 m (39.4 ft.). On an LVD bus
with a single device, make this length shorter than 25 m (82 ft.). The
SAITe1300-S internal cable length is 25 cm (9.8 in.).

• SCSI cables cannot be branched.

1

Make sure that the host computer and the SAITe1300-S are off.

2

Connect the SCSI cable and terminator as shown below.

The SCSI cable can be up to 24.7 m (81 ft.) long. (The SAITe1300-S
internal cable length is 25 cm (9.8 in.).)

A SCSI bus allows you to connect up to fifteen peripherals to the host computer,
including the unit.

Host computer

SCSI connector

SCSI cable

Terminator

«
...
25
26
27
28
29
...
»

Содержание SAITe1300-F



















































Отзывы:

Нет отзывов

Похожие инструкции для SAITe1300-F

Бренд: XOLTA Страницы: 40

ValueLoader LTO-1

Бренд: Quantum Страницы: 76

Бренд: GrainPro Страницы: 19

Бренд: Lifetime Страницы: 96

Бренд: Magnusson Страницы: 18

Бренд: Accu Страницы: 44

Бренд: Vivo Страницы: 3

SOHORAID SR8-TB3

Бренд: Stardom Страницы: 29

Бренд: Husky Страницы: 4

Huge Media Vault - Dual Max

Бренд: Huge Systems Страницы: 26

Бренд: PQI Страницы: 7

Бренд: Supercmicro Страницы: 90

Бренд: Seagate Technology Страницы: 36

Бренд: LaCie Страницы: 23

Бренд: BLUM Страницы: 2

Бренд: Pig Страницы: 25

Бренд: Pacetti Страницы: 8

Бренд: Freecom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды