Adjustment Using the Menus
29
FUNCTION BUTTON SETTING
About the function assigned to the
function button
SCAN
Press the button to change the scan size of the picture
according to the setting of “STANDARD” or
“FULL+NATIVE” selected in SCAN (page 26).
ASPECT
Press the button to set the aspect ratio of the picture, 4:3
or 16:9.
Note
The panel of LMD-2451W is 16:10 and the panel of
LMD-1751W is 15:9.
When the 16:9 signal is displayed, black bars appear in
the upper and lower positions of the display. This is not
a malfunction. (See “Scan mode image” on page 26.)
EXT SYNC (external sync)
Press the button to operate the unit on an external sync
signal through the EXT SYNC IN connector.
EXT SYNC works when the component/RGB signals
are input.
BLUE ONLY
Press the button to eliminate the red and green signals.
Only blue signal is displayed as an apparent
monochrome picture on the screen. This facilitates
“chroma” and “phase” adjustments and observation of
VCR noise.
MONO
Press the button to display a monochrome picture. When
the buttons is pressed again, the monitor switches
automatically to color mode.
MARKER
Press the button to display the marker. Set the aspect
marker and safety area size in the MARKER SETTING
menu (see page 27).
H/V DELAY
Press the button to observe the horizontal and vertical
sync signals at the same time.
MULTI DISPLAY
Press the button to display the multi display. Set the
multi display setting in the MULTI DISPLAY
SETTING menu (see page 28).
CLOSED CAPTION
Press the button to display the closed caption. Set the
closed caption setting in the CLOSED CAPTION
SETTING menu (see page 30).
Not available for the signal input from BKM-227W.
APA (Auto Pixel Alignment)
Press the button to adjust the picture automatically to
maximum clarity for the signal input to the HD15 input
connector. For finer according to the input signal, see
“DOT PHASE” on page 25.
When the menu screen is displayed, the APA does not
function.
POSITION
Sets the position of the sub display. You
can select from among 1 to 3 for the 4:3
display and 1 to 4 for the 16:9 display.
4:3 display
•
1:
Top
•
2:
Center
•
3:
Bottom
16:9 display
•
1:
Bottom left
•
2:
Bottom right
•
3:
Top right
•
4:
Top left
FRAME
Sets the position of the main display
when MULTI DISPLAY is set to POP
and the sub display is put on the 4:3
display.
•
RIGHT:
The main display is put by
the right side of the sub display.
•
LEFT:
The main display is put by the
left side of the sub display.
SUB PICTURE
SIZE (LMD-2451W
only)
Sets the size of the sub picture. You can
select from among 1 to 3. When the
setting is high, the size becomes large.
Submenu
Setting
F1 BUTTON to F4
BUTTON
Assigns the function to the function
buttons of the front panel and turns the
function on or off.
You can assign the function from among
SCAN, ASPECT, EXT SYNC, BLUE
ONLY, MONO, MARKER, H/V
DELAY, MULTI DISPLAY, CLOSED
CAPTION, APA and I/P MODE.
Factory setting
•
F1 button:
EXT SYNC
•
F2 button:
SCAN
•
F3 button:
ASPECT
•
F4 button:
H/V DELAY
Submenu
Setting
F 1 B U T T O N :
xxxx
F 2 B U T T O N :
xxxx
F 3 B U T T O N :
xxxx
F 4 B U T T O N :
xxxx
USER CONFIG – FUNCTION BUTTON SETTING
Содержание LMD1751WCC
Страница 41: ...Sony Corporation ...
