Chapter 10
Setup Menus
Chapter 10
Setup Menus
10-7
10-3 Items in the Basic Setup Menu
The basic setup menu contains the following items.
In the “Settings” column of the table, the factory
default settings are underlined.
Item number
Item name
Settings
001
PREROLL TIME
0S to 5S to 30S:
Set the preroll time to between 0 and 30 seconds. A preroll
time of at least 5 seconds is recommended when using this unit for editing.
002
a)
CHARACTER H-
POSITION
Adjust the horizontal screen position of the character information output from the
COMPOSITE VIDEO OUTPUT 3(SUPER) connector, HDSDI OUTPUT
3(SUPER) connector, and SDI OUTPUT 3(SUPER) connector for superimposed
display on the monitor.
00 to 1E to 3C (59.94i, 29.97PsF, 23.98PsF mode)/00 to 1B to 36 (50i, 25PsF,
24PsF mode):
The hexadecimal value 00 is for the far left of the screen and
increasing the value moves the position of the characters to the right.
003
a), b)
CHARACTER V-
POSITION
Adjust the vertical screen position of the first line of the character information
output from the COMPOSITE VIDEO OUTPUT 3(SUPER) connector, HDSDI
OUTPUT 3(SUPER) connector, and SDI OUTPUT 3(SUPER) connector for
superimposed display on the monitor.
00 to 57 to 6C (59.94i, 29.97PsF, 23.98PsF mode)/00 to 70 to 88 (50i, 25PsF,
24PsF mode):
The hexadecimal value 00 is for the top of the screen and
increasing the value lowers the position of the characters.
004
SYNCHRONIZE
When editing using this unit as a controller and an external VTR connected to this
unit via a 9-pin remote control cable, this item determines whether or not to
operate the two units in phase synchronization.
OFF:
Do not operate in phase synchronization.
ON :
Operate in phase synchronization.
006
LOCAL FUNCTION
ENABLE
Determines which buttons on the control panel are enabled when this unit is
controlled from external equipment.
DIS:
All buttons and switches are disabled.
S&E&F :
Only the STOP button, EJECT button, and F1 to F6 buttons are
enabled.
ENA:
All buttons and switches are enabled.
MAP:
Follow the LOCAL KEY MAP setting.
For information about setting the LOCAL KEY MAP, see menu item 023 LOCAL
KEY MAP (page 10-9).
005
DISPLAY INFORMATION
SELECT
Determines the kind of character information to be output from the COMPOSITE
VIDEO OUTPUT 3(SUPER) connector, HDSDI OUTPUT 3(SUPER) connector,
and SDI OUTPUT 3(SUPER) connector when F4 (CHARA) in function menu
page 4 is set to ON.
T&STA :
Time data display information and the unit’s status
T&UB:
Time data display information and the user’s bits
T&CTL:
Time data display information and CTL
T&T:
Time data display information and time code (LTC or VITC)
TIME:
Time code (LTC or VITC) only
If there is an overlap between the setting of this item and the setting of the control
panel, it is automatically avoided. For example, if CTL is selected on the control
panel and this menu item setting is T&CTL, then CTL and LTC are output.
a)When setting items 002 and 003, watch the monitor
screen, and adjust to the required state.
007
TAPE TIMER DISPLAY
Determines whether to display the CTL count in 12-hour mode or 24-hour mode.
+ –12H :
12-hour mode
24H:
24-hour mode
008
MONITORING
SELECTION FOR VTR-
TO-VTR EDIT
For recorder-player editing with only one monitor connected to the recorder,
determines whether the recorder is forced into E-E mode when the recorder’s
PLAYER button is pressed to view the player’s playback signals on the monitor.
MANU :
Do not force the recorder into E-E mode.
AUTO:
Force the recorder into E-E mode.
b)
When displaying time code values, there is a slight time
delay. Therefore, when creating a tape for off-line
editing, the information inserted in the upper half of the
screen may be delayed by one frame.
Note
(Continued)
