HAP-Z1ES
76
Pin No.
Pin Name
I/O
Description
C9
RTC_XTALO
O
Real time clock output terminal (32.768 kHz)
C10
GND24
-
Ground terminal
C11
POR_B
I
Reset signal input from reset signal generator and system controller “L”: reset
C12
BOOT_MODE0
I
Boot mode setting terminal Fixed at “L”
C13
SD3_DAT5
-
Not used
C14
SATA_REXT
-
Terminal for the impedance calibration
C15
NANDF_CLE
O
Update signal output to the system controller “H”: update
C16
NANDF_CS1
O
Reset signal output to the remote commander code learning processor “L”: reset
C17
NANDF_D1
I/O
Two-way data bus terminal Not used
C18
NANDF_D7
-
Not used
C19
SD4_DAT5
I/O
Two-way data bus with the
fl
ash memory
C20
SD1_DAT1
I/O
Two-way data bus terminal Not used
C21
SD2_CLK
-
Not used
C22
RGMII_TD0
O
RGMII transmit data output to the ethernet transceiver
C23
RGMII_TX_CTL
O
RGMII transmit data enable signal output to the ethernet transceiver
C24
RGMII_RD0
I
RGMII receive data input from the ethernet transceiver
C25
EIM_D16
-
Not used
D1
CSI_D1M
-
Not used
D2
CSI_D1P
-
Not used
D3
GND27
-
Ground terminal
D4
CSI_REXT
-
Not used
D5
CLK2_P
-
Not used
D6
GND28
-
Ground terminal
D7
CLK1_P
O
Clock signal (positive) output to the FPGA
D8
GND29
-
Ground terminal
D9
RTC_XTALI
I
Real time clock input terminal (32.768 kHz)
D10
USB_H1_VBUS
I
Power supply of the USB interface for the WLAN/BT COMBO card
D11
PMIC_ON_REQ
O
Not used
D12
ONOFF
-
Not used
D13
SD3_DAT4
-
Not used
D14
SD3_CLK
-
Not used
D15
SD3_RST
-
Not used
D16
NANDF_CS3
-
Not used
D17
NANDF_D3
-
Not used
D18, D19
SD4_DAT0,
SD4_DAT7
I/O
Two-way data bus with the
fl
ash memory
D20
SD1_CLK
O
Clock signal output terminal Not used
D21
RGMII_TXC
O
RGMII transmit clock signal output to the ethernet transceiver
D22
RGMII_RX_CTL
I
RGMII receive data valid signal input from the ethernet transceiver
D23
RGMII_RD3
I
RGMII receive data input from the ethernet transceiver
D24
EIM_D18
-
Not used
D25
EIM_D23
I
Status signal input from the FPGA
E1
CSI_D2M
-
Not used
E2
CSI_D2P
-
Not used
E3
CSI_D0P
-
Not used
E4
CSI_D0M
-
Not used
E5 to E7
GND30 to GND32
-
Ground terminal
E8
NVCC_PLL_OUT
-
Power supply terminal for the PLL output Not used
E9
USB_OTG_VBUS
I
Power supply of the USB interface for the USB connector
E10
USB_H1_DP
I/O
Two-way USB data (positive) with the WLAN/BT COMBO card
E11
TAMPER
I
Mode setting terminal Fixed at “H”
E12
TEST_MODE
I
Mode setting terminal Not used
E13
SD3_DAT6
-
Not used
E14
SD3_DAT0
-
Not used
E15
NANDF_WP_B
O
LED drive signal output terminal “H”: LED on
E16
SD4_CLK
O
Clock signal output to the
fl
ash memory
E17
NANDF_D6
-
Not used
E18
SD4_DAT4
I/O
Two-way data bus with the
fl
ash memory
E19
SD1_DAT2
I/O
Two-way data bus terminal Not used
E20
SD2_DAT1
-
Not used
Содержание HAP-Z1ES
Страница 119: ...MEMO HAP Z1ES 119 ...