Sony Handycam Vision CCD-TRV107E, Руководство по обслуживанию

Страница: 30 / 170

1-20
CCD-TRV107E/TRV108E/TRV208E/TRV408E
89
Troubleshooting
Поиск
и
устранение
неисправностей
— Troubleshooting —
English
Types of trouble and their solutions
If you run into any problem using your camcorder, use the following table to troubleshoot the
problem. If the problem persists, disconnect the power source and contact your Sony dealer or local
authorised Sony service facility. If “C:
ss
:
ss
” appears on the screen, the self-diagnosis display
function has worked. See page 93.
In the recording mode
Symptom Cause and/or Corrective Actions
• The POWER switch is set to OFF (CHG) or PLAYER.
c
Set it to CAMERA. (p. 26)
• The tape has run out.
c
Rewind the tape or insert a new one. (p. 24, 38)
• The write-protect tab is set to expose the red mark.
c
Use a new tape or slide the tab. (p. 25)
• The tape is stuck to the drum (moisture condensation).
c
Remove the cassette and leave your camcorder for at least 1
hour to acclimatize. (p. 108)
• While being operated in CAMERA mode, your camcorder has
been in the standby mode for more than 5 minutes.
c
Set the POWER switch to OFF (CHG) and then to CAMERA
again. (p. 26)
• The battery pack is dead or nearly dead.
c
Install a fully charged battery pack. (p. 15, 16)
• The viewfinder lens is not adjusted.
c
Adjust the viewfinder lens. (p. 31)
• STEADYSHOT is set to OFF in the menu settings.
c
Set it to ON. (p. 79)
• The wide mode is set to 16:9FULL.
c
Set it to OFF. (p. 79)
• The setting is the manual focus mode.
c
Press FOCUS to return to the autofocus mode. (p. 55)
• Shooting conditions are not suitable for autofocus.
c
Adjust to focus manually. (p. 55)
• The video heads may be dirty.
c
Clean the heads using the Sony V8-25CLD cleaning cassette
(optional). (p. 109)
• The LCD panel is open.
c
Close the LCD panel. (p. 28)
• The contrast between the subject and background is too high.
This is not a malfunction.
(Continued on the following page)
START/STOP does not operate.
The power goes off.
The image on the viewfinder screen
is not clear.
The autofocusing function does not
work.
The SteadyShot function does not
work.*
The picture does not appear in the
viewfinder.
A vertical band appears when you
shoot a subject such as lights or a
candle flame against a dark
background.
The
x
indicator flashes in the
viewfinder.
90
Types of trouble and their solutions
Symptom Cause and/or Corrective Actions
• This is not a malfunction.
• If 10 minutes elapse after you set the POWER switch to
CAMERA or DEMO MODE is set to ON in the menu settings
without a cassette inserted, your camcorder automatically
starts the demonstration.
c
Insert a cassette and the demonstration stops.
You can also cancel DEMO MODE. (p. 82)
• NIGHTSHOT is set to ON.
c
Set it to OFF. (p. 34)
• NIGHTSHOT is set to ON in a bright place.
c
Set it to OFF or use the NightShot function in a dark place.
(p. 34)
• The backlight function is working.
c
Cancel it. (p. 33)
• Set STEADYSHOT to OFF in the menu setting. (P. 79)
* CCD-TRV408E only
In the playback mode
Symptom Cause and/or Corrective Actions
• The POWER switch is set to CAMERA or OFF (CHG).
c
Set it to PLAYER. (p. 38)
• The tape has run out.
c
Rewind the tape. (p. 38)
• The television’s video programme position is not adjusted
correctly.
c
Adjust it. (p. 42)
• EDIT is set to ON in the menu settings.
c
Set it to OFF. (p. 80)
• The video head may be dirty.
c
Clean the heads using the Sony V8-25CLD cleaning cassette
(optional). (p. 109)
• The volume is turned to minimum.
c
Open the LCD panel and press . (p. 38)
The picture appears too bright, and
the subject does not appear on the
screen.
The picture is recorded in incorrect or
unnatural colours.
The tape does not move when a
video control button is pressed.
A horizontal black band appears
when shooting a TV screen or
computer screen.*
No sound or only a low sound is
heard when playing back a tape.
The playback picture is not clear or
does not appear.
The playback button does not work.
An unknown picture is displayed on
the screen.
A vertical band appears when you
shoot a very bright subject.
91
Troubleshooting
Поиск
и
устранение
неисправностей
In the recording and playback modes
Symptom Cause and/or Corrective Actions
• The battery pack is not installed, or is dead or nearly dead.
c
Install a charged battery pack. (p. 15, 16)
• The AC power adaptor is not connected to a wall socket.
c
Connect the AC power adaptor to a wall socket. (p. 20)
• The tape was ejected after recording.
• You have not recorded on the cassette yet.
• The operating temperature is too low.
• The battery pack is not fully charged.
c
Charge the battery pack fully again. (p. 15, 16)
• The battery pack is completely dead, and cannot be recharged.
c
Replace with a new battery pack. (p. 15)
• You have used the battery pack in an extremely hot or cold
environment for a long time.
• The battery pack is completely dead, and cannot be recharged.
c
Replace with a new battery pack. (p. 15)
• The battery pack is not fully charged.
• A deviation has occurred in the remaining battery time.
c
Charge the battery pack fully again. (p. 15, 16)
• A deviation has occurred in the remaining battery time.
c
Charge the battery pack fully again so that the indication on
the battery remaining indicator is correct. (p. 15, 16)
• The power source is disconnected.
c
Connect it firmly. (p. 15, 20)
• The battery pack is dead.
c
Use a charged battery pack. (p. 15, 16)
• Moisture condensation has occurred.
c
Remove the cassette and leave your camcorder for at least 1
hour to acclimatize. (p. 108)
• The
q
REMAIN is set to AUTO in the menu settings.
c
Set it to ON to always display the remaining tape indicator.
Types of trouble and their solutions
The battery pack discharges quickly.
The remaining battery time
indicator does not indicate
the correct time.
The power does not turn on.
The
%
and
Z
indicators flash and no
functions except for cassette ejection
work.
The cassette cannot be removed from
the holder.
The power goes off although the
remaining battery time indicator
indicates that the battery pack has
enough power to operate.
The end search function does not
work.
The remaining tape indicator is not
displayed.
(Continued on the following page)
92
Others
Symptom Cause and/or Corrective Actions
• Your VCR and/or video camera recorder is not set correctly.
c
Make sure the input selector of the VCR is set to LINE. Also,
make sure the power switch of the video camera is set to
VTR/VCR. (p. 68)
• The IR SETUP code or PAUSE MODE is not set correctly.
c
Select the correct IR SETUP code and PAUSE MODE,
according to your VCR. Then confirm VCR operation with
the IR TEST function. (p. 69 to 73)
• COMMANDER is set to OFF in the menu settings.
c
Set it to ON. (p. 83)
• Something is blocking the infrared rays.
c
Remove the obstacle.
• The batteries are inserted in the battery holder with the
+ – polarities incorrectly matching the + – marks.
c
Insert the batteries with the correct polarity. (p. 125)
• The batteries are dead.
c
Insert new ones. (p. 125)
•Set the date and time. (p. 22)
• Moisture condensation has occurred.
c
Remove the cassette and leave your camcorder for at least 1
hour to acclimatize. (p. 108)
• Some troubles have occurred in your camcorder.
c
Remove the cassette and insert it again, then operate your
camcorder.
• Disconnect the mains lead of the AC power adaptor or remove
the battery pack, then reconnect it after about 1 minute. Turn
the power on (p. 20, 26). If the functions still do not work, press
RESET using a sharp-pointed object. (If you press RESET, all
the settings including the date and time return to the default.)
(p. 123)
• The AC power adaptor is disconnected.
c
Connect it firmly. (p. 20)
• The battery pack is not installed.
c
Install it properly. (p. 15)
• Something is wrong with the battery pack.
c
Contact your Sony dealer or local authorised Sony service
facility.
• The POWER switch is not set to OFF (CHG).
c
Set it to OFF (CHG).
Types of trouble and their solutions
The Remote Commander supplied
with your camcorder does not
work.*
The melody or beep sounds for 5
seconds.
While charging the battery pack, no
indicator appears or the indicator
flashes in the display window.
No function works though the power
is on.
You cannot charge the battery pack
installed to your camcorder.
Easy Dubbing does not function.
The date or time indicator does not
appear, and the bars
“--:--:--” appear.
* CCD-TRV107E/TRV208E/TRV408E only