Sonifex Redbox RB-DSD8 Скачать руководство пользователя страница 37

Страница: 37 / 40

Redbox RB-DSD8 User Handbook

TECHNICAL SPECIFICATION

TECHNIC

AL SPECIFIC

TION

PSU LEDs:

Show the state of each power supply

Remote Control LED:

Show if remote control is selected

External Synchronisation
LED:

Show the state of any synchronisation inputs used.

Rear Panel - Operational Controls

Silence Threshold:

-27dBfs to -84dBfs in 3dBfs steps, via rear panel DIPSwitches

Silence Duration:

0 - 254 seconds in 2 second intervals duration, via rear

panel DIPSwitches

Stereo/Mono Switching: Stereo or mono, via rear panel DIPSwitch

Master Output Sample

32, 44.1, 48, 88.2, 96,176.4 or 192kHz, via rear panel

Rate Select:

DIPSwitches

Ignore Silence:

Each channel can be set to ignore silences, via rear panel

DIPswitches

Remote Control Enable:

Enabled or disabled, via rear panel DIPswitch

Synchronisation Mode

Synchronisation in master mode or synchronisation from

& Source Select:

MAIN input1, AES or wordclock synchronisation input in auto

or slave mode, via rear panel DIPswitches

Remote Start:

Latched or momentary, via DIPswitch

Input Lock Loss:

Switch immediately or treat as silence delay, via rear panel

DIPswitch

Digital or Analogue

Digital or analogue, via rear panel DIPswitches

Output:

Full Scale Line Up:

24, 18 or 12 dBu = 0dBFS, via rear panel DIPswitches

Boot Mode:

Boot in boot or normal via rear panel DIPswitch

Connections

Digital/Analogue Inputs: 2 x 8 stereo channel inputs on 2 x 25 pin D-type male

Digital/Analogue Outputs: 1 x 8 stereo channel outputs on 1 x 25 pin D-type female

Synchronisation Inputs:

1 x BNC (Wordclock or AES/EBU)

Remote I/O Port:

25 way D-type female

Содержание Redbox RB-DSD8









































Результаты поиска

Содержание Redbox RB-DSD8

Отзывы:

Бренды по названию

Популярные бренды

Sonifex Redbox RB-DSD8, Руководство пользователя

Результаты поиска

Содержание Redbox RB-DSD8

Отзывы:

Бренды по названию

Популярные бренды