manualshive.com logo in svg

Sonifex Redbox RB-DSD8, Руководство пользователя

Поделиться
Скачать
Sonifex Redbox RB-DSD8 Скачать руководство пользователя страница 18

6

Redbox RB-DSD8 User Handbook

3. Rear Panel DIPSwitch Settings

Fig 3-1: RB-DSD8 Rear Panel DIPSwitches

Rear Panel DIPSwitches: Bank 1 SILENCE LEVEL AND DURATION  

Silence Detect Interval Control (DIPSwitches 1-7, Bank 1)

DIPSwitch

1

2

3

4

5

6

7

Seconds

2

4

8

16 32 64 128

The silence detect interval DIPSwitches adjust the duration over which a silence is detected 
before alarming and ranges from 2-254 seconds by combining raised (ON) DIPSwitches in 2 
second intervals with 0  being all DIPSwitches down. The default value is set at 30 seconds 
but can be changed using the serial port or ethernet. This time can also be overridden by a 
remote GPI/O input that sets the unit to an override time that is set to 2mins 5 seconds. 

Silence Detect Trigger Level (DIPSwitches 8-11, Bank 1)

DIPSwitch

8

9

10 11

Level dBFS

-3

-6

-12 -24

The trigger level DIPSwitches adjust the level below which silence detection occurs. This 
level may be varied from -27dBFS to -84dBFS in 3db steps by raising different combinations 
(to ON). Please note the range changes depending on the full scale settings. These 
represent -15dBU to -60 dBU

Full Scale

Min

Max

12dBU

-27dBFS

-72dBFS

18dBU

-33dBFS

-78dBFS

24dBU

-39dBFS

-84dBFS

Stereo/Mono Switch (DIPSwitch 12, Bank 1)

The configuration of this defines whether you want to switch sources when left and/or 
right channel of the incoming source go silent. When channels are linked the stereo mode 
becomes multichannel mode and any single mono channel failure will cause the unit to 
switch sources; likewise mono mode will require both channels to fail individually before 
switching sources.

REAR PANEL DIPSWITCH SETTINGS

3

REAR P

ANEL DIPSWIT

CH SE

T

TINGS

Содержание Redbox RB-DSD8









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды