manualshive.com logo in svg

sonible d24, Руководство пользователя

Поделиться
Скачать
sonible d24 Скачать руководство пользователя страница 40

d:24 owner‘s manual

40

9   MAINTENANCE & UPDATE

For safe and reliable operation, the dust filter of the front panel, be

-

hind the grilles, should be removed and cleaned regularly to ensure 
maximum airflow through the device.

To clean the dust filter, the panel can be removed by unscrewing 

eight M3 TX10 screws on the top and the bottom of the panel.

If you want to completely replace the filter, you additionally have 

to remove the display by unfastening

 

the four M3 TX10 screws. 

Please be very careful with FPC cable when removing the display!

Please use original filter sets provided by the local distributor or by 

sonible.

9.1   Maintenance

If the dust filter is not maintained there will be safety risks. There 

is also a risk that the unit will malfunction since it is dependent on 

constant airflow from front to rear. If the dust filters are not clean 

and the unit malfunctions, any resultant problems will not be cover-
ed by the warranty.

Feel free to contact us by email: 

[email protected]

.

If the amplifier malfunctions due to dirty dust-filters, any required repairs or 

 

resultant drop out costs are not covered by the warranty.

Содержание d24



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды