Sonex Aircraft Aerovee 2.1 Скачать руководство пользователя страница 59

Страница: 59 / 70

AeroVee 2.1

Rev Z. 01/14/2015

Sonex Aircraft

LLC

The AeroVee requires the use of baffles to direct air over and

through the piston barrels and cylinder heads. The system

must designed and installed to keep the cylinder head within

their operating limits during normal operation.
Sonex Aircraft LLC has developed a fence baffle system

specifically for use on Sonex Airframes /AeroVee installations.

These system may also be adapted to other airframe installa-

tions.
Each fence baffle comes with its own instructions for fitting.

ENGINE COOLING BAFFLES

An AeroConversions' fence baffle fitted to a Sonex airframe. The installation shown here has a bottom-mounted oil cooler.

Available Fence Baffle Systems

__ SNX-P30-10, For a Sonex, Waiex, or Xenos airframe.
__ ONX-P01-10, For a Onex airframe.

Содержание Aerovee 2.1





































































Результаты поиска

Содержание Aerovee 2.1

Отзывы:

Бренды по названию

Популярные бренды

Sonex Aircraft Aerovee 2.1, Сборка и инструкция по установке

Результаты поиска

Содержание Aerovee 2.1

Отзывы:

Бренды по названию

Популярные бренды